Industries

View as List Grid

Items 1-20 of 76

Page
per page
Set Descending Direction
  1. Stacking Clips
    Use these clips to stack empty ICC NW Econo-totes. Learn More
    As low as $52.95
  2. Valve Seats
    Valve seats seal the valve body against the disk to stop flow. Learn More
    As low as $15.00
  3. Valve Kit Econo Tote
    The valve kit for ICC NW's 2 Ton Econo Tote includes (2) 2"IN Butterfly Valves, (1) Sample Valve, (1) dial thermometer Learn More
  4. Fuji Temp & Parts
    The Fuji controller receives information from the temperature sensor and sends open/close signals to the Heat Transfer Jacket solenoid valve. It can also operate direct fire Burners/Immersion Heaters/Etc. Learn More
    As low as $250.00
  5. Pressure Gauge
    The range of a pressure gauge should be approximately twice the operating pressure of the vessel. ICC NW stocks 30 lb. Liquid filled gauges with 1/4 in. pipe thread connections. It is important to "burp" gauges periodically. Peel the black rubber stopper at the top of the valve back until pressure is released. Learn More
    As low as $35.00
  6. P.A.M. Pressure Gauge
    The P.A.M. Spool Assembly groups the necessary fittings together for tank pressure regulation. The standard spool assembly consists of a pressure gauge, ball valve, and an open TC port. Does not include a P.R.V. Learn More
    As low as $35.00
  7. Thermometer
    Thermometer face is 2-1/2 in. diameter and has a 1/2 in. MNPT threaded connection. Temperature range reads from 0 to 250 deg. F (-20 to 120 deg.C). Learn More
    As low as $31.50
  8. Sample Valve TC
    The sample valve is designed to accommodate a CO2 test meter. Learn More
    As low as $155.00
  9. Level Gauge Valve & Parts
    The 3-way level gauge valve will mount to a 1-1/2 IN TC at the base of a ICC NW level gauge system. This valve allows you to isolate the level gauge. 304 SS mat. The sight tube is translucent PFA Teflon. Make sure the tube insert is used at all tubing connections. Learn More
    As low as $1.12
  10. P.R.V.
    The P.R.V. are available for 2 or 3IN TC vent. The valve opens at 0.9 lb. pressure and 0.089 lb. vacuum. Full 304 stainless steel body construction. Learn More
    As low as $180.65
  11. Solenoid Valve
    A brass Solenoid Valve is used to regulate coolant. The strength of brass is needed for the constant valve cycling. Learn More
    As low as $156.00
  12. P.A.M. Tree Parts
    The P.A.M. Tree assembly groups the necessary fittings for tank pressure regulation together at the end of the vent extension line. The standard tree assembly consists of a pressure gauge, ball valve, and an open TC port. Does not include a P.R.V. Learn More
    As low as $7.95
  13. 5/8" Level Gauge Compression Fitting
    Compression fittings are used to connect the polysulphone and stainless steel tubing found in the level gauge assembly. Learn More
    As low as $29.95
  14. DIN Cap
    The DIN cap is used to seal the end of a tube, fitting, or valve which has a DIN threaded ferrule. A gasket and DIN nut will attach the cap. 304 SS mat. Metric sizes available. Learn More
    As low as $12.50
  15. DIN Gasket
    DIN gaskets fit into a threaded DIN ferrule to complete the seal. Learn More
    As low as $1.05
  16. DIN Nut
    The DIN nut accompanies the plain DIN ferrule and is tightened with a DIN wrench. The nut serves the same function as a clamp in a TC connection. 304 SS mat. Metric sizes available. Learn More
    As low as $17.85
  17. DIN Ferrule, Threaded End
    The DIN threaded ferrule is one side of a three piece DIN connection. The threaded ferrule connects to the female threaded DIN nut. 304 SS mat. Metric sizes available. Learn More
    As low as $12.90
  18. Poly TC Cap
    The clear TC cap attaches to a TC ferrule for viewing. These caps are not designed to be used under pressure. Caution must be used in tightening the clamp as the cap can crack. Learn More
    As low as $8.85
  19. TC Clamp
    The TC clamp is used to clamp two TC ferrules together. A TC gasket is installed between the ferrule for a complete seal. 304 Stainless Steel. Learn More
    As low as $7.25
  20. TC Ferrule
    The TC ferrule is one end of a three part connection. This is the most commonly used type of sanitary process pipe connection. Ferrules have 1.125" necks. Longer and shorter necks are available. 304 Stainless Steel. Learn More
    As low as $4.45
View as List Grid

Items 1-20 of 76

Page
per page
Set Descending Direction