Brewery
-
5/8" Level Gauge Compression FittingCompression fittings are used to connect the polysulphone and stainless steel tubing found in the level gauge assembly. Installation Directions: Tighten nut 'finger tight', continue to tighten 1-1/4" turns with a wrench. The small ferrule (2) will permanently adhere to level gauge tubing. CAUTION: Over tighten will result in fine fracture lines in the level gauge tubing. Learn MoreAs low as $29.95
-
Parts for Lauter TunUHMWPE Plates, Rod Wipers, Seals - Everything you need to maintain your lauter tun Learn MoreAs low as $12.62
-
Parts for 18x22 Oval GrainoutParts for 18" x 22" Oval Grainout Manway. Side mount. Used on atmospheric tanks only. 304 SS. Learn MoreAs low as $3.59
-
Parts for 16x22 Oval Grainout ManwayParts for 16" x 22" Oval Grainout Manway. Side mount. Used on atmospheric tanks only. Learn MoreAs low as $3.59
-
Butterfly Valves w Metric HandleThe butterfly valve is used in process flow piping where fractional flow control is required. The valve has a stainless steel body with a silicon valve seat. TC connections shown. Other connections and butt-weld ends available on all butterfly valves. 304 SS mat. Learn MoreAs low as $378.00
-
Butterfly Valves w Knob HandleThe butterfly valve is used in process flow piping where fractional flow control is required. The valve has a stainless steel body with a silicon valve seat. TC connections shown. Other connections and butt-weld ends available on all butterfly valves. 304 SS mat. Learn MoreAs low as $305.78
-
Butterfly ValvesThe butterfly valve is used in process flow piping where fractional flow control is required. The valve has a stainless steel body with a silicon valve seat. TC connections shown. Other connections and butt-weld ends available on all butterfly valves. 304 SS mat. Learn MoreAs low as $89.00
-
Valve SeatsValve seats seal the valve body against the disk to stop flow. Learn MoreAs low as $15.00
-
Fuji Temp & PartsThe Fuji controller receives information from the temperature sensor and sends open/close signals to the Heat Transfer Jacket solenoid valve. It can also operate direct fire Burners/Immersion Heaters/Etc. Learn MoreAs low as $35.00
-
Pressure GaugeThe range of a pressure gauge should be approximately twice the operating pressure of the vessel. ICC NW stocks 30 lb. Liquid filled gauges with 1/4 in. pipe thread connections. It is important to "burp" gauges periodically. Peel the black rubber stopper at the top of the valve back until pressure is released. Learn MoreAs low as $38.00
-
P.A.M. Pressure GaugeThe P.A.M. Spool Assembly groups the necessary fittings together for tank pressure regulation. The standard spool assembly consists of a pressure gauge, ball valve, and an open TC port. Does not include a P.R.V. Learn MoreAs low as $38.00
-
ThermometerThermometer face is 2-1/2 in. diameter and has a 1/2 in. MNPT threaded connection. Temperature range reads from 0 to 250 deg. F (-20 to 120 deg.C). Learn MoreAs low as $31.50
-
Sample Valve TCThe sample valve is designed to accommodate a CO2 test meter. Learn MoreAs low as $192.00
-
Level Gauge Valve & PartsThe 3-way level gauge valve will mount to a 1-1/2 IN TC at the base of a ICC NW level gauge system. This valve allows you to isolate the level gauge. 304 SS mat. The sight tube is translucent PFA Teflon. Make sure the tube insert is used at all tubing connections. Learn MoreAs low as $1.50
-
Solenoid ValveA brass Solenoid Valve is used to regulate coolant. The strength of brass is needed for the constant valve cycling. Learn MoreAs low as $156.00
-
P.A.M. Tree PartsThe P.A.M. Tree assembly groups the necessary fittings for tank pressure regulation together at the end of the vent extension line. The standard tree assembly consists of a pressure gauge, ball valve, and an open TC port. Does not include a P.R.V. Learn MoreAs low as $7.95
-
5/8" Level Gauge Compression FittingCompression fittings are used to connect the polysulphone and stainless steel tubing found in the level gauge assembly. Learn MoreAs low as $29.95
-
DIN CapThe DIN cap is used to seal the end of a tube, fitting, or valve which has a DIN threaded ferrule. A gasket and DIN nut will attach the cap. 304 SS mat. Metric sizes available. Learn MoreAs low as $12.50
-
DIN GasketDIN gaskets fit into a threaded DIN ferrule to complete the seal. Learn MoreAs low as $1.05
-
DIN NutThe DIN nut accompanies the plain DIN ferrule and is tightened with a DIN wrench. The nut serves the same function as a clamp in a TC connection. 304 SS mat. Metric sizes available. Learn MoreAs low as $17.85