Processing
-
Valve SeatsValve seats seal the valve body against the disk to stop flow. Learn MoreAs low as $15.00
-
DIN CapThe DIN cap is used to seal the end of a tube, fitting, or valve which has a DIN threaded ferrule. A gasket and DIN nut will attach the cap. 304 SS mat. Metric sizes available. Learn MoreAs low as $12.50
-
DIN GasketDIN gaskets fit into a threaded DIN ferrule to complete the seal. Learn MoreAs low as $1.05
-
DIN NutThe DIN nut accompanies the plain DIN ferrule and is tightened with a DIN wrench. The nut serves the same function as a clamp in a TC connection. 304 SS mat. Metric sizes available. Learn MoreAs low as $17.85
-
DIN Ferrule, Threaded EndThe DIN threaded ferrule is one side of a three piece DIN connection. The threaded ferrule connects to the female threaded DIN nut. 304 SS mat. Metric sizes available. Learn MoreAs low as $12.90
-
Poly TC CapThe clear TC cap attaches to a TC ferrule for viewing. These caps are not designed to be used under pressure. Caution must be used in tightening the clamp as the cap can crack. Learn MoreAs low as $8.85
-
TC ClampThe TC clamp is used to clamp two TC ferrules together. A TC gasket is installed between the ferrule for a complete seal. 304 Stainless Steel. Learn MoreAs low as $7.25
-
TC FerruleThe TC ferrule is one end of a three part connection. This is the most commonly used type of sanitary process pipe connection. Ferrules have 1.125" necks. Longer and shorter necks are available. 304 Stainless Steel. Learn MoreAs low as $4.45
-
Gaskets - Top OutswingTop mount inspection manway accommodates right, left, and top hinge locations. Cool-to-touch (outdoors) high impact PVC grip knob. Hygienic dome lid and narrow cross arms allow complete wash-down, no puddles. 360 degree locations. Learn MoreAs low as $125.00
-
Gaskets for Sanitary Pressure Outswing ManwayGasket will fit Top Outswing Manways. They are available in Buna, Viton, Silicone and EPDM Learn MoreAs low as $125.00
-
LED replacement bulbThe tank light is used to illuminate the inside of a vessel while brewing or cleaning. It mounts to a 2 in. TC fitting. A standard 120 volt circuit and a 50 watt bulb are required. Learn MoreAs low as $420.00
-
Tank LightThe tank light is used to illuminate the inside of a vessel while brewing or cleaning. It mounts to a 2 in. TC fitting. A standard 120 volt circuit and a 50 watt bulb are required. Learn MoreOut of stock
-
Sanitary Hinged Lid PartsAvailable with sliding doors, removable doors, and CIP-able options as well as double half circle hatches with fixed or removable bridge. Learn MoreAs low as $2.65
-
DIN WrenchThe DIN wrench is used to fully tighten the DIN nut to the DIN ferrule Learn MoreAs low as $41.50
-
Sprayball PartsSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn MoreAs low as $4.95
-
In-Line Sight Glass LensThe in-line site glass is used for product viewing. Order does include Replacement lense only. Learn MoreAs low as $41.75
-
In-Line Sight Glass GasketThe in-line site glass is used for product viewing. The site glass has a TC ferrule on each end. The clear portion is either Pyrex or glass. One end unscrews to replace lens and gaskets. Gaskets come in a package of 2 Learn MoreAs low as $13.50
-
In-Line Sight Glass 4-boltThe in-line site glass is used for product viewing. The site glass has a TC ferrule on each end. The clear portion is either Pyrex or glass. One end unscrews to replace lens and gaskets. Learn MoreAs low as $266.00
-
Food Grade GreasePETROL-GEL(R) is a food-grade lubricant. It should be used on stainless steel and brass thread connections to reduce the risk of seizure. CAUTION: Product contact to PETROL-GEL(R) can contribute to "flat" beer. Learn MoreAs low as $4.95
-
Sani-SpinThe Sani-Spin is used much the same way as a C.I.P. sprayball. The advantage of the Sani-Spin is the force of it’s spinning action and the minimal volume it requires. For example, the optimum operating condition for a C.I.P. sprayball is 40 GPM @ 25 PSI; where as the Sani-Spin requires just 25 GPM @ 30 PSI. Learn MoreOut of stock