Search results for: 'VALVE-SEAT SILICONE 1 1/2IN''
- Related search terms
- VALVE-SEAT SILICONE 1 1/2IN
- silicone #358
- silicone+gasket
-
Valve SeatsValve seats seal the valve body against the disk to stop flow. Learn MoreAs low as $12.65 -
Butt Weld FittingsButt weld fittings connect with pipe or tubing to deliever product. Learn MoreAs low as $7.50 -
TC GasketThe gasket seats between two TC ferrules. Buna is the most common material used for temperature between -22F to +250F. Viton is commonly used for temperature up to 400F Silicone but not for low temperature. Teflon are used for higher temperature applications depending on customer preference. Learn MoreAs low as $0.18 -
Ball ValvesThe stainless steel ball valve has female threaded pipe connections, and is a "full port" valve (the flow is not restricted). 316 SS mat. Learn MoreAs low as $48.75 -
Butterfly ValvesThe butterfly valve is used in process flow piping where fractional flow control is required. The valve has a stainless steel body with a silicon valve seat. TC connections shown. Other connections and butt-weld ends available on all butterfly valves. 304 SS mat. Learn MoreAs low as $120.92 -
Rupture DiskA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. Learn MoreAs low as $17.60 -
Level Gauge Valve & PartsThe 3-way level gauge valve will mount to a 1-1/2 IN TC at the base of a ICC NW level gauge system. This valve allows you to isolate the level gauge. 304 SS mat. The sight tube is translucent PFA Teflon. Make sure the tube insert is used at all tubing connections. Learn MoreAs low as $1.50 -
Bevel Seat FittingsBevel Seat Fittings are used on process equipment and piping to ensure rigidity of the system. Bevel Seat Unions consist of a Threaded Ferrule mated with a Plain Ferrule. Learn MoreAs low as $1.19 -
Solenoid ValveA brass Solenoid Valve is used to regulate coolant. The strength of brass is needed for the constant valve cycling. Learn MoreAs low as $52.81 -
Sample Valve TCThe sample valve is designed to accommodate a CO2 test meter. Learn MoreAs low as $0.78
-
Sample Valve MNPTThe sample valve is designed to accommodate a CO2 test meter. Learn MoreAs low as $0.78
-
Mixer SealsParts for ICC NW Mixers including: bottom entry, side entry, top entry. Learn MoreAs low as $127.50
-
Replacement Coil - Solenoid ValveA brass Solenoid Valve is used to regulate coolant. The strength of brass is needed for the constant valve cycling. Learn MoreAs low as $56.70 -
Butt Weld Fitting - TeeButt Weld tees are a simplified manifold used to regulate fluid direction. Learn MoreAs low as $9.50 -
TRI CLAMP x MNPTA TC x MNPT will adapt a TC (TRI-CLAMP) ferrule to female pipe fittings. One end is TC and the other is male threaded pipe. 304 SS mat. Learn MoreAs low as $13.75 -
Butterfly Valve Seat 2IN Silicone for H&H ValvesValve Seat for H&H Butterfly Valves 2IN Learn More$17.00 -
TC Cap x TC Ferrule (centered)TC adapters are an economical alternative to a concentric reducer. This fitting is used to reduce the size in process piping where turbulence and complete drainage of the product is not a concern. 304 SS mat. Learn MoreAs low as $13.75
