Fittings & Valves
-
Butt Weld Fitting - TeeButt Weld tees are a simplified manifold used to regulate fluid direction. Learn MoreAs low as $9.99
-
I-Line GasketsSanitary I-Line Gaskets. Available in Buna, EPDM, Teflon (PTFE) & Viton (FKM) Learn MoreAs low as $1.35
-
Butterfly ValvesThe butterfly valve is used in process flow piping where fractional flow control is required. The valve has a stainless steel body with a silicon valve seat. TC connections shown. Other connections and butt-weld ends available on all butterfly valves. 304 SS mat. Learn MoreAs low as $89.00
-
Valve SeatsValve seats seal the valve body against the disk to stop flow. Learn MoreAs low as $17.00
-
Solenoid ValveA brass Solenoid Valve is used to regulate coolant. The strength of brass is needed for the constant valve cycling. Learn MoreAs low as $429.68
-
DIN CapThe DIN cap is used to seal the end of a tube, fitting, or valve which has a DIN threaded ferrule. A gasket and DIN nut will attach the cap. 304 SS mat. Metric sizes available. Learn MoreAs low as $8.40
-
DIN GasketDIN gaskets fit into a threaded DIN ferrule to complete the seal. Learn MoreAs low as $0.75
-
DIN NutThe DIN nut accompanies the plain DIN ferrule and is tightened with a DIN wrench. The nut serves the same function as a clamp in a TC connection. 304 SS mat. Metric sizes available. Learn MoreAs low as $12.30
-
DIN Ferrule, Threaded EndThe DIN threaded ferrule is one side of a three piece DIN connection. The threaded ferrule connects to the female threaded DIN nut. 304 SS mat. Metric sizes available. Learn MoreAs low as $8.90
-
TC ClampThe TC (Tri-Clamp) is used to clamp two TC ferrules together. A TC gasket (sold separately) is installed between the ferrules for a complete seal. 304 stainless steel material. Learn MoreAs low as $2.54
-
TC FerruleThe TC ferrule is one end of a three part connection. This is the most commonly used type of sanitary process pipe connection. Ferrules have 1.125" necks. Longer and shorter necks are available. 304 Stainless Steel. Learn MoreAs low as $3.60
-
DIN WrenchThe DIN wrench is used to fully tighten the DIN nut to the DIN ferrule Learn MoreAs low as $23.20
-
Replacement Coil - Solenoid ValveA brass Solenoid Valve is used to regulate coolant. The strength of brass is needed for the constant valve cycling. Learn MoreAs low as $139.50
-
Check ValveA check valve with a ten pound spring is used with carbonation stone assemblies to prevent product back-flow. Check valves are available with male or female pipe thread connections. Learn MoreAs low as $138.00
-
Ball ValvesThe stainless steel ball valve has female threaded pipe connections, and is a "full port" valve (the flow is not restricted). 316 SS mat. Learn MoreAs low as $221.60
-
TC/Gas Fitting AssemblyThe TC x Gas Fitting is used to add a CO2-Nitrogen mix to your serving tank. We can also add a carbonation "stone" to the TC fitting and use the assembly to carbonate your beer. Learn MoreAs low as $17.50
-
TC TeeThe TC has three TC ferrules for multi-purpose application. Custom branch sizes and butt-weld tees available. 304 SS mat. Learn MoreAs low as $23.00
-
TC Eccentric ReducerEccentric reducers are used for tubing size transitions. The flat side allows complete drainage in horizontal piping. Custom reducers, additional sizes and butt-weld available. 304 SS mat. Learn MoreAs low as $44.38
-
TC Concentric ReducerConcentric reducers are used for TC transitions in vertical tubing. Custom reducers, additional sizes and butt-weld available. 304 SS mat. Learn MoreAs low as $36.99