Tank Accessories

View as List Grid

Items 1-20 of 35

Page
per page
Set Descending Direction
  1. Limit Switch
    As low as $10.00
  2. In-Line Sight Glass
    The in-line site glass is used for product viewing. The site glass has a TC ferrule on each end. The clear portion is either Pyrex or glass. One end unscrews to replace lens and gaskets. Gaskets come in a package of 2 Learn More
    As low as $158.40
  3. Floating Lid Tube
    Tubes are designed for ICC NW varying capacity storage tanks. Please consult chart for correct size, questions please call (503) 468-6560. Our tube forumla changed in 2021. Learn More
    As low as $0.64
  4. FLOATING LID MANIFOLD ASSEMBLY
    Manifold is attached to floating lid tube to inflate and deflate the tube. Learn More
  5. 5/8" Level Gauge Compression Fitting
    Compression fittings are used to connect the polysulphone and stainless steel tubing found in the level gauge assembly. Installation Directions: Tighten nut 'finger tight', continue to tighten 1-1/4" turns with a wrench. The small ferrule (2) will permanently adhere to level gauge tubing. CAUTION: Over tighten will result in fine fracture lines in the level gauge tubing. Learn More
    As low as $43.64
  6. Parts for Lauter Tun
    UHMWPE Plates, Rod Wipers, Seals - Everything you need to maintain your lauter tun Learn More
    As low as $6.60
  7. Fuji Temp & Parts
    The Fuji controller receives information from the temperature sensor and sends open/close signals to the Heat Transfer Jacket solenoid valve. It can also operate direct fire Burners/Immersion Heaters/Etc. Learn More
    As low as $198.00
  8. Pressure Gauge
    The range of a pressure gauge should be approximately twice the operating pressure of the vessel. ICC NW stocks 30 lb. Liquid filled gauges with 1/4 in. pipe thread connections. It is important to "burp" gauges periodically. Peel the black rubber stopper at the top of the valve back until pressure is released. Learn More
    As low as $12.50
  9. Thermometer
    Thermometer face is 2-1/2 in. diameter and has a 1/2 in. MNPT threaded connection. Temperature range reads from 0 to 250 deg. F (-20 to 120 deg.C). Learn More
    As low as $33.00
  10. Sample Valve TC
    The sample valve is designed to accommodate a CO2 test meter. Learn More
    As low as $159.20
  11. Level Gauge Valve & Parts
    The 3-way level gauge valve will mount to a 1-1/2 IN TC at the base of a ICC NW level gauge system. This valve allows you to isolate the level gauge. 304 SS mat. The sight tube is translucent PFA Teflon. Make sure the tube insert is used at all tubing connections. Learn More
    As low as $1.50
  12. P.R.V.
    The P.R.V. are available for 2IN, 3IN and 4IN TC vent. Full 304 stainless steel body construction. Learn More
    As low as $312.00
  13. P.A.M. Tree Parts
    The P.A.M. Tree assembly groups the necessary fittings for tank pressure regulation together at the end of the vent extension line. The standard tree assembly consists of a pressure gauge, ball valve, and an open TC port. Does not include a P.R.V. Learn More
    As low as $8.18
  14. 5/8" Level Gauge Compression Fitting
    Compression fittings are used to connect the polysulphone and stainless steel tubing found in the level gauge assembly. Learn More
    As low as $43.64
  15. Poly TC Cap
    The clear TC cap attaches to a TC ferrule for viewing. These caps are not designed to be used under pressure. Caution must be used in tightening the clamp as the cap can crack. Learn More
    As low as $12.00
  16. Tank Light
    The tank light is used to illuminate the inside of a vessel while brewing or cleaning. It mounts to a 2 in. TC fitting. A standard 120 volt circuit and a 50 watt bulb are required. Learn More
    As low as $5.00
  17. Rupture Disk
    A rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. Learn More
    As low as $400.00
  18. Standpipe
    For use in bottom-cone fermentation tanks, includes FDA silicone O-Ring Learn More
    As low as $30.00
  19. Ice Shield
    An ice shield is commonly welded to tanks to be a universal mounting device for individual controllers. Learn More
    As low as $50.00
  20. Sprayballs & Parts
    Sprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn More
    As low as $3.50
View as List Grid

Items 1-20 of 35

Page
per page
Set Descending Direction