Search results for: 'tank check valves'
- Related search terms
- check valve rebuild
- check valve ass
- tank door wing nut and brass screw
-
Check ValveA check valve with a ten pound spring is used with carbonation stone assemblies to prevent product back-flow. Check valves are available with male or female pipe thread connections. Learn MoreAs low as $138.00 -
Butterfly ValvesThe butterfly valve is used in process flow piping where fractional flow control is required. The valve has a stainless steel body with a silicon valve seat. TC connections shown. Other connections and butt-weld ends available on all butterfly valves. 304 SS mat. Learn MoreAs low as $120.92 -
Ball ValvesThe stainless steel ball valve has female threaded pipe connections, and is a "full port" valve (the flow is not restricted). 316 SS mat. Learn MoreAs low as $48.75 -
Tank LightThe tank light is used to illuminate the inside of a vessel while brewing or cleaning. It mounts to a 2 in. TC fitting. A standard 120 volt circuit and a 50 watt bulb are required. Learn MoreAs low as $25.00 -
Valve SeatsValve seats seal the valve body against the disk to stop flow. Learn MoreAs low as $12.65 -
VALVE-CHECK 3/8IN MNPT X 3/8IN MNPT 10 PSI 316A check valve with a ten pound spring is used with carbonation stone assemblies to prevent product back-flow. Check valves are available with male or female pipe thread connections. Learn More$138.00 -
Temperature ControllerIs temperature control specifically designed for use in wineries and breweries. Learn MoreAs low as $96.00 -
Butterfly Valve Seat 2IN Silicone for H&H ValvesValve Seat for H&H Butterfly Valves 2IN Learn More$17.00 -
Butterfly Valve Seat 1.5 Silicone for H&H ValvesValve Seat for H&H Butterfly Valves 1.5IN - Fit HH30415 Learn More$15.00 -
Parts for Shadowless Inswing/Outswing ManwayParts for 16" x 22" Shadowless (Flushmount) Inswing/Outswing Manway. Completely Flush interior. No cleaning shadow. Side mount. Standard is 304 SS. Call if 316L is required. Door plates are custom-made. Call for price and lead time. Learn MoreAs low as $41.97 -
HINGE ARM ASS'Y-16X22 IN/OUTSWING FLUSHMOUNT MW NON-INSLT'D TANKHINGE ARM ASS'Y-16X22 IN/OUTSWING FLUSHMOUNT MW NON-INSLT'D TANK Learn More$215.00 -
Rupture DiskA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. Learn MoreAs low as $17.60 -
Sprayballs & PartsSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn MoreAs low as $3.50 -
Oxy Carb Tee AssemblyThe tee assembly is used to inject gas into the product. A hollow capped tube of cintered stainless is welded to a TC ferrule and clamped to a customized TC tee. This assembly includes a special tee, cintered stone, check valve, 3/8" hose barb, clamp and gasket. 304 SS mat. Learn MoreAs low as $524.00 -
Low Level SensorThe low level sensor is an on/off float switch. The float should mount at the low level limit of a tank. Most commonly used in a hot liquor tank. Learn MoreAs low as $154.00 -
P.A.M. Tree PartsThe P.A.M. Tree assembly groups the necessary fittings for tank pressure regulation together at the end of the vent extension line. The standard tree assembly consists of a pressure gauge, ball valve, and an open TC port. Does not include a P.R.V. Learn MoreAs low as $8.18 -
Sample Valve TCThe sample valve is designed to accommodate a CO2 test meter. Learn MoreAs low as $0.78 -
Sample Valve MNPTThe sample valve is designed to accommodate a CO2 test meter. Learn MoreAs low as $0.78
-
TEE ASSY OXY-CARBSTONE 1 1/2INThe tee assembly is used to inject gas into the product. A hollow capped tube of cintered stainless is welded to a TC ferrule and clamped to a customized TC tee. This assembly includes a special tee, cintered stone, check valve, 3/8" hose barb, clamp and gasket. 304 SS mat. Learn More$524.00 -
RUPTURE DISC-2IN TC (60 PSI) 200°F (ASME) PTFE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 60.00 PSIG @ 200°F TYPE SR-H Learn More$400.00
