Search results for: 'GASKET-MW G&H 20IN BUNA'
- Related search terms
- gasket-mw g'
- gasket-mw g'a=0''[0]
- gasket-mw g'a=0'a=0',(;))
-
Hot
PRESSURE GAUGE 0-100 PSI 2.5IN DIAL, REAR MOUNT, 1/4IN MNPT CONNThe range of a pressure gauge should be approximately twice the operating pressure of the vessel. Learn More$24.00 -
LENS (ONLY) FOR SIGHT GLASS 1.5IN, POLYSULPHONEThe in-line site glass is used for product viewing. Order does include Replacement lense only. 1.75"wide x 1.75" thick x .125"thick Learn More$26.41 -
PRESSURE RELIEF VALVE, GUTH VENT, 0.9 LB, 3IN TC, (134-0105)The P.R.V. attaches to a 3IN TC vent. Valve relieves pressure as the fluid level rises while filling a tank Valve relieves vacuum as the fluid level drops while emptying a tank Seals under equal pressure Full body 316 stainless steel construction 1/4" FNPT connection for gas inlet, plug is included Vacuum break: , 0.1 PSI Pressure relief: 0.9 PSI Maximum temperature and pressure rating: 3 PSI @ 70°F Maximum flow rate: 500 GPM Learn More$312.00 -
LENS (ONLY) FOR SIGHT GLASS 2IN, PYREXThe in-line site glass is used for product viewing. Order includes replacement lense only. 2.5" wide x 4" long x 0.156" thick. Learn More$28.82 -
(7A) VALVE-LEVEL GAUGE VALVE PLUG 33810 AISI 304LVALVE-LEVEL GAUGE VALVE PLUG SPOUT Learn More$31.75 -
Parts for Lauter TunUHMWPE Plates, Rod Wipers, Seals - Everything you need to maintain your lauter tun Learn MoreAs low as $6.60 -
TEE ASSY OXY-CARBSTONE 1 1/2INThe tee assembly is used to inject gas into the product. A hollow capped tube of cintered stainless is welded to a TC ferrule and clamped to a customized TC tee. This assembly includes a special tee, cintered stone, check valve, 3/8" hose barb, clamp and gasket. 304 SS mat. Learn More$524.00 -
Low Level SensorThe low level sensor is an on/off float switch. The float should mount at the low level limit of a tank. Most commonly used in a hot liquor tank. Learn MoreAs low as $154.00 -
Sani-SpinThe Sani-Spin is used much the same way as a C.I.P. sprayball. The advantage of the Sani-Spin is the force of it’s spinning action and the minimal volume it requires. For example, the optimum operating condition for a C.I.P. sprayball is 40 GPM @ 25 PSI; where as the Sani-Spin requires just 25 GPM @ 30 PSI. Learn MoreAs low as $618.00 -
RUPTURE DISC-2IN TC (60 PSI) 200°F (ASME) PTFE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 60.00 PSIG @ 200°F TYPE SR-H Learn More$400.00 -
RUPTURE DISC-2IN TC (75 PSI) 75°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 75PSIG @ 75°F Learn More$600.00 -
Hot
RUPTURE DISK-2IN TC (110 PSI) 200°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 110.00 PSIG @ 200°F TYPE AXIUS SC Learn More$400.00 -
RUPTURE DISC-1 1/2IN TC (130 PSI) 300°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 1 1/2IN TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 130.0 PSIG @ 300°F Learn More$1,368.00 -
RUPTURE DISC-2IN TC (88.3 PSI) 72°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 88.3 PSIG @ 72°F SR-H TYPE Learn More$400.00 -
RUPTURE DISC-2IN TC (25 PSI) 72°F (ASME) 316L EPDMThe rupture disc fits between 2IN TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Replace the disk every 5-6 years depending on the use of the tank to ensure superior performance. Learn More$689.00Out of stock
