Search results for: 'level gauge valve and parts'
- Related search terms
- Level gauge valve seal
- level 40 pokemon go for sale,【Site: Cg4s.com】pokemon switch account,pogo accounts,free pokemon tcg accounts,free op pokemon go a
- level 50 pokemon go account for sale,【Site: Cg4s.com】best pokemon account,account pokemon unite,pokemon go accounts for sale lev
-
GASKET-PRV 2IN 60 DUROThe P.R.V. attaches to a 2 IN. TC vent or P.A.M. assembly. The valve is easy to take apart and clean. 15 lb. and 25 lb. pressure springs are available. Relief pressure can be adjusted down 5 lb. The valve will open at 0.089 lb. of vacumm. Full stainless steel body construction. Material: Silicone Learn More$3.95 -
TEE ASSY OXY-CARBSTONE 1 1/2INThe tee assembly is used to inject gas into the product. A hollow capped tube of cintered stainless is welded to a TC ferrule and clamped to a customized TC tee. This assembly includes a special tee, cintered stone, check valve, 3/8" hose barb, clamp and gasket. 304 SS mat. Learn More$524.00 -
Mixer SealsParts for ICC NW Mixers including: bottom entry, side entry, top entry. Learn MoreAs low as $127.50 -
FUJI CONTROLLER PXR4 DIGITALThe Fuji controller receives information from the temperature sensor and sends open/close signals to the Heat Transfer Jacket solenoid valve. It can also operate direct fire Burners/Immersion Heaters/Etc. Learn More$350.00 -
RUPTURE DISC-2IN TC (60 PSI) 200°F (ASME) PTFE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 60.00 PSIG @ 200°F TYPE SR-H Learn More$400.00 -
SPRAYBALL-2.5IN X 1IN- BOTTOM SPRAY - 316LSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. DIA X 1IN DIA SLIP JOINT BOTTOM SPRAY PATTERN 316L Learn More$47.64 -
SPRAYBALL-2.5IN X 1IN- TOP SPRAYSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn More$41.00 -
RUPTURE DISC-2IN TC (75 PSI) 75°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 75PSIG @ 75°F Learn More$600.00 -
Hot
RUPTURE DISK-2IN TC (110 PSI) 200°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 110.00 PSIG @ 200°F TYPE AXIUS SC Learn More$400.00 -
RUPTURE DISC-1 1/2IN TC (130 PSI) 300°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 1 1/2IN TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 130.0 PSIG @ 300°F Learn More$1,368.00 -
RUPTURE DISC-2IN TC (88.3 PSI) 72°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 88.3 PSIG @ 72°F SR-H TYPE Learn More$400.00 -
RUPTURE DISC-2IN TC (25 PSI) 72°F (ASME) 316L EPDMThe rupture disc fits between 2IN TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Replace the disk every 5-6 years depending on the use of the tank to ensure superior performance. Learn More$689.00Out of stock -
Tank LightThe tank light is used to illuminate the inside of a vessel while brewing or cleaning. It mounts to a 2 in. TC fitting. A standard 120 volt circuit and a 50 watt bulb are required. Learn MoreAs low as $25.00 -
PIN, COTTER FOR SPRAYBALL-2.5IN DIA X 1IN DIA SLIP JOINTSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn More$3.50 -
COTTER PIN 2.5INSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn More$4.95 -
Sani-SpinThe Sani-Spin is used much the same way as a C.I.P. sprayball. The advantage of the Sani-Spin is the force of it’s spinning action and the minimal volume it requires. For example, the optimum operating condition for a C.I.P. sprayball is 40 GPM @ 25 PSI; where as the Sani-Spin requires just 25 GPM @ 30 PSI. Learn MoreAs low as $618.00 -
THERMOMETER-DIAL 3IN X 1/2IN MNPT, 4IN STEM, REAR MNT. 0-250 DEG F (WIKA)Thermometer face is 3IN. diameter and has a 1/2 in. MNPT threaded connection. 4IN stem. Rear mounted. Temperature range reads from 0 to 250 deg. F Learn More$78.00
-
Hot
THERMOMETER-DIAL 3IN X 1/2IN MNPT, 12IN STEM, REAR MNT. 0-250 FThermometer face is 3IN. diameter and has a 1/2 in. MNPT threaded connection. 12IN stem. Rear mounted. Temperature range reads from 0 to 250 deg. F Learn More$73.50 -
THERMOMETER-DIAL 5IN X 1/2IN MNPT, 9IN STEM, REAR MNT, 0-250 FThermometer face is 5IN. diameter and has a 1/2 in. MNPT threaded connection. 9IN stem. Rear mounted. Temperature range reads from 0 to 250 deg. F Learn More$96.95 -
Hot
LIGHT WORT RECEIVER RIGID MARINE DUALLY SERIES 60121 SURFACE MOUNTIt produces 1,568 lumens. 1 per box. Kit includes: Stainless steel mounting bracket and hardware. - Bracket for surface mount only. Hardwired. Learn More$90.19
