Search results for: 'gasket-mw g'
- Related search terms
- gasket-mw g'A=0
- gasket-mw g'a=0'
- gasket-mw g'a=0'A=0
-
Solenoid ValveA brass Solenoid Valve is used to regulate coolant. The strength of brass is needed for the constant valve cycling. Learn MoreAs low as $52.81 -
Poly TC CapThe clear TC cap attaches to a TC ferrule for viewing. These caps are not designed to be used under pressure. Caution must be used in tightening the clamp as the cap can crack. Learn MoreAs low as $12.00 -
Sanitary Hinged Lid PartsAvailable with sliding doors, removable doors, and CIP-able options as well as double half circle hatches with fixed or removable bridge. Learn MoreAs low as $3.50 -
P.A.M. SpoolThe P.A.M. Spool Assembly groups the necessary fittings together for tank pressure regulation. The standard spool assembly consists of a pressure gauge, ball valve, and an open TC port. Does not include a P.R.V. Learn MoreAs low as $83.25 -
(11) Compression InsertThe 3-way level gauge valve will mount to a 1-1/2 in. TC at the base of a ICC NW level gauge system. This valve allows you to isolate the level gauge. 304 SS mat. The sight tube is translucent PFA Teflon. Make sure the tube insert is used at all tubing connections. Compression insert 1/2" for 5/8 for PTFE Tube .5IN OD for 5/8IN PTFE Tube Learn More$19.39 -
TC 45° ElbowThe 45° elbow has TC connections on each end. TC elbows allow lines to be broken down for cleaning. Additional sizes and butt-weld elbows available. 304 or 316L SS mat. Learn MoreAs low as $9.42 -
P.A.M. Tree PartsThe P.A.M. Tree assembly groups the necessary fittings for tank pressure regulation together at the end of the vent extension line. The standard tree assembly consists of a pressure gauge, ball valve, and an open TC port. Does not include a P.R.V. Learn MoreAs low as $8.18 -
Sani-Spin Sprayball with 1IN Slip JointThe Sani-Spin is used much the same way as a C.I.P. sprayball. The advantage of the Sani-Spin is the force of it’s spinning action and the minimal volume it requires. For example, the optimum operating condition for a C.I.P. sprayball is 40 GPM @ 25 PSI; where as the Sani-Spin requires just 25 GPM @ 30 PSI. Learn More$618.00 -
Replacement Coil - Solenoid ValveA brass Solenoid Valve is used to regulate coolant. The strength of brass is needed for the constant valve cycling. Learn MoreAs low as $56.70 -
TC TeeThe TC has three TC ferrules for multi-purpose application. Custom branch sizes and butt-weld tees available. 304 SS mat. Learn MoreAs low as $27.00 -
TC Eccentric ReducerEccentric reducers are used for tubing size transitions. The flat side allows complete drainage in horizontal piping. Custom reducers, additional sizes and butt-weld available. 304 SS mat. Learn MoreAs low as $25.25
-
(3) KNUCKLE BLOCK ASSEMBLYSide mount. For 18IN bubble outswing manway and 18x22 and 16x22 oval grainout manway. Will fit 18x22IN and 16x22IN oval grainout manway 18IN bubble manway Learn More$231.89 -
Fuji Temp & PartsThe Fuji controller receives information from the temperature sensor and sends open/close signals to the Heat Transfer Jacket solenoid valve. It can also operate direct fire Burners/Immersion Heaters/Etc. Learn MoreAs low as $198.00 -
StandpipeFor use in bottom-cone fermentation tanks, includes FDA silicone O-Ring Learn MoreAs low as $30.00 -
Temperature SensorTemperature probe used to sense current product temperature. To be used in conjunction with a temperature controller. Sensors have a spring-loaded probe designed to fit a 12 in. tempwell with a 1/2 inch MNPT fitting. Learn MoreAs low as $109.60 -
Low Level SensorThe low level sensor is an on/off float switch. The float should mount at the low level limit of a tank. Most commonly used in a hot liquor tank. Learn MoreAs low as $154.00
