Search results for: 'gasket-mw g'a=0'a=0',(;))'
- Related search terms
- gasket-mw g'a=0'
- gasket-mw g'a=0'A=0
- gasket-mw g'a=0')) AND 5404=5404 AND ((6355=6355
-
O-RING-BUNA 18.25IN ID X .375IN THK (OLD SKU NUMBER 10450840/10450850)Gasket (O-Ring) for Bottom Cone Manway. Material: Buna Learn More$73.77 -
CLAMP-TC 304 2.5IN 13MHM SINGLE PINThe TC clamp is used to clamp two TC ferrules together. A TC gasket is installed between the ferrule for a complete seal. 304 Stainless Steel. Learn More$4.28 -
CLAMP-TC 304 .5IN & .75IN 13MHM SINGLE PINThe TC clamp is used to clamp two TC ferrules together. A TC gasket is installed between the ferrule for a complete seal. 304 Stainless Steel. Learn More$3.81 -
ThermometerThermometer face is 2-1/2 in. diameter and has a 1/2 in. MNPT threaded connection. Temperature range reads from 0 to 250 deg. F (-20 to 120 deg.C). Learn MoreAs low as $33.00 -
Sanitary Hinged Lid PartsAvailable with sliding doors, removable doors, and CIP-able options as well as double half circle hatches with fixed or removable bridge. Learn MoreAs low as $3.50 -
Poly TC CapThe clear TC cap attaches to a TC ferrule for viewing. These caps are not designed to be used under pressure. Caution must be used in tightening the clamp as the cap can crack. Learn MoreAs low as $12.00 -
TC 45° ElbowThe 45° elbow has TC connections on each end. TC elbows allow lines to be broken down for cleaning. Additional sizes and butt-weld elbows available. 304 or 316L SS mat. Learn MoreAs low as $9.42 -
(3) KNUCKLE BLOCK ASSEMBLYSide mount. For 18IN bubble outswing manway and 18x22 and 16x22 oval grainout manway. Will fit 18x22IN and 16x22IN oval grainout manway 18IN bubble manway Learn More$231.89 -
Hi-Low Level ControlThe hi-low level control is used to regulate wort receiver levels. Commonly used on both the brewpub open wort receiver and the enclosed airless grant. Wetted parts are 316 Stainless Steel. Learn MoreAs low as $272.27 -
(11) Compression InsertThe 3-way level gauge valve will mount to a 1-1/2 in. TC at the base of a ICC NW level gauge system. This valve allows you to isolate the level gauge. 304 SS mat. The sight tube is translucent PFA Teflon. Make sure the tube insert is used at all tubing connections. Compression insert 1/2" for 5/8 for PTFE Tube .5IN OD for 5/8IN PTFE Tube Learn More$19.39 -
Fuji Temp & PartsThe Fuji controller receives information from the temperature sensor and sends open/close signals to the Heat Transfer Jacket solenoid valve. It can also operate direct fire Burners/Immersion Heaters/Etc. Learn MoreAs low as $198.00 -
TC Eccentric ReducerEccentric reducers are used for tubing size transitions. The flat side allows complete drainage in horizontal piping. Custom reducers, additional sizes and butt-weld available. 304 SS mat. Learn MoreAs low as $25.25
-
TC TeeThe TC has three TC ferrules for multi-purpose application. Custom branch sizes and butt-weld tees available. 304 SS mat. Learn MoreAs low as $27.00 -
TC Cap x TC Ferrule (offset)TC cap adapters are an economical alternative to an eccentric reducer. This fitting is used to reduce the size in process piping where turbulence and complete drainage of the product is not a concern. 304 SS mat. Learn MoreAs low as $19.99 -
ADAPTER-E33208 CLAMP ADAPTER ASEPTOFLEX VARIO 1.5IN TC 316LADAPTER-E33208 CLAMP ADAPTER ASEPTOFLEX VARIO 1.5IN TC 316L Learn More$67.50 -
(2) Cross Arm Assembly 3-ArmHeavy-duty 7ga outswing door and wing nuts swing free and clear of opening. . Triple cross arm for strong seal. Learn More$624.90
-
Sani-Spin Sprayball with 1IN Slip JointThe Sani-Spin is used much the same way as a C.I.P. sprayball. The advantage of the Sani-Spin is the force of it’s spinning action and the minimal volume it requires. For example, the optimum operating condition for a C.I.P. sprayball is 40 GPM @ 25 PSI; where as the Sani-Spin requires just 25 GPM @ 30 PSI. Learn More$618.00 -
Replacement Coil - Solenoid ValveA brass Solenoid Valve is used to regulate coolant. The strength of brass is needed for the constant valve cycling. Learn MoreAs low as $56.70
