Search results for: 'door plate ass'A=0'
- Related search terms
- door wingnut with brass'A=0
- door wing nut'A=0
- DOOR THREAD
-
GASKET-PRV 2IN 60 DUROThe P.R.V. attaches to a 2 IN. TC vent or P.A.M. assembly. The valve is easy to take apart and clean. 15 lb. and 25 lb. pressure springs are available. Relief pressure can be adjusted down 5 lb. The valve will open at 0.089 lb. of vacumm. Full stainless steel body construction. Material: Silicone Learn More$3.95 -
(1) PRESSURE RELIEF VALVE- E RING SHAE C-10105The P.R.V. attaches to a 2 IN TC vent or P.A.M. assembly. The valve is easy to take apart and clean. 15 lb. and 25 lb. pressure springs are available. Relief pressure can be adjusted down 5 lb. The valve will open at 0.089 lb. of vacumm. Full stainless steel body construction. Learn More$3.49 -
VALVE-CHECK 3/8IN MNPT X 3/8IN MNPT 10 PSI 316A check valve with a ten pound spring is used with carbonation stone assemblies to prevent product back-flow. Check valves are available with male or female pipe thread connections. Learn More$138.00 -
(7A) VALVE-LEVEL GAUGE VALVE PLUG 33810 AISI 304LVALVE-LEVEL GAUGE VALVE PLUG SPOUT Learn More$31.75 -
Parts for Bottom Cone ManwayParts for Bottom Cone manway for fermentation tanks. Learn MoreAs low as $0.53 -
STAINLESS STEEL WASHER 3/4IN ID FOR OVAL GRAINOUT AND BOTTOM CONE MANWAYSThis part can be used for the following manways: Oval-grainout, Bottom cone manways Learn More$0.53 -
Sprayballs & PartsSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn MoreAs low as $3.50 -
DIN CapThe DIN cap is used to seal the end of a tube, fitting, or valve which has a DIN threaded ferrule. A gasket and DIN nut will attach the cap. 304 SS mat. Metric sizes available. Learn MoreAs low as $8.40 -
DIN Ferrule, Threaded EndThe DIN threaded ferrule is one side of a three piece DIN connection. The threaded ferrule connects to the female threaded DIN nut. 304 SS mat. Metric sizes available. Learn MoreAs low as $12.34 -
DIN NutThe DIN nut accompanies the plain DIN ferrule and is tightened with a DIN wrench. The nut serves the same function as a clamp in a TC connection. 304 SS mat. Metric sizes available. Learn MoreAs low as $12.30 -
ThermometerThermometer face is 2-1/2 in. diameter and has a 1/2 in. MNPT threaded connection. Temperature range reads from 0 to 250 deg. F (-20 to 120 deg.C). Learn MoreAs low as $33.00 -
Poly TC CapThe clear TC cap attaches to a TC ferrule for viewing. These caps are not designed to be used under pressure. Caution must be used in tightening the clamp as the cap can crack. Learn MoreAs low as $12.00 -
Ball ValvesThe stainless steel ball valve has female threaded pipe connections, and is a "full port" valve (the flow is not restricted). 316 SS mat. Learn MoreAs low as $48.75 -
TC 45° ElbowThe 45° elbow has TC connections on each end. TC elbows allow lines to be broken down for cleaning. Additional sizes and butt-weld elbows available. 304 or 316L SS mat. Learn MoreAs low as $9.42
