Search results for: 'manway gasket 20.5 inch''
- Related search terms
- gasket-mw g'A=0
- gasket mw G&H 18in epdm
- gasket-mw g'a=0'") ORDER BY 2319-- pjjo'
-
CLEVIS PIN .75 x 2.175Use a clevis pin as part of a clevis fastener. When threaded through the prongs of a tang and secured with a cotter pin, this fastening system allows movement along one axis while restricting it along the other. The clevis pin is used on the following ICC NW manways - 16X22 Shroud / Flushmount. Learn More$41.97 -
(5) HINGE BRACKET-SWIVELSwivel Hinge Bracket fits our top mount inspection manway and accommodates right, left, and top hinge locations. Learn More$46.69 -
Screw Cap Hex 1/2INThis part can be used for the following manways: BTM CONE MANWAY Learn More$0.70 -
NUT-NYLOCK 3/4INThis part can be used for the following manways: BTM CONE MANWAY, 18IN BUBBLE OUTSWING Learn More$1.12 -
Hot
LIGHT WORT RECEIVER RIGID MARINE DUALLY SERIES 60121 SURFACE MOUNTIt produces 1,568 lumens. 1 per box. Kit includes: Stainless steel mounting bracket and hardware. - Bracket for surface mount only. Hardwired. Learn More$90.19 -
Butterfly Valve Seat 1.5 Silicone for H&H ValvesValve Seat for H&H Butterfly Valves 1.5IN - Fit HH30415 Learn More$15.00 -
P.R.V.The P.R.V. are available for 2IN, 3IN and 4IN TC vent. Full 304 stainless steel body construction. Learn MoreAs low as $312.00 -
PRESSURE RELIEF VALVE, GUTH VENT, 0.9 LB, 3IN TC, (134-0105)The P.R.V. attaches to a 3IN TC vent. Valve relieves pressure as the fluid level rises while filling a tank Valve relieves vacuum as the fluid level drops while emptying a tank Seals under equal pressure Full body 316 stainless steel construction 1/4" FNPT connection for gas inlet, plug is included Vacuum break: , 0.1 PSI Pressure relief: 0.9 PSI Maximum temperature and pressure rating: 3 PSI @ 70°F Maximum flow rate: 500 GPM Learn More$312.00 -
Tank LightThe tank light is used to illuminate the inside of a vessel while brewing or cleaning. It mounts to a 2 in. TC fitting. A standard 120 volt circuit and a 50 watt bulb are required. Learn MoreAs low as $25.00 -
(11) Compression InsertThe 3-way level gauge valve will mount to a 1-1/2 in. TC at the base of a ICC NW level gauge system. This valve allows you to isolate the level gauge. 304 SS mat. The sight tube is translucent PFA Teflon. Make sure the tube insert is used at all tubing connections. Compression insert 1/2" for 5/8 for PTFE Tube .5IN OD for 5/8IN PTFE Tube Learn More$19.39 -
CAP-DIN 80 METRIC-IMPERIAL 304 DIN 11851 UNIONThe DIN cap is used to seal the end of a tube, fitting, or valve which has a DIN threaded ferrule. A gasket and DIN nut will attach the cap. 304 SS mat. Metric sizes available. Learn More$39.00 -
CAP-DIN 32 METRIC-IMPERIAL 304 DIN 11851 UNIONThe DIN cap is used to seal the end of a tube, fitting, or valve which has a DIN threaded ferrule. A gasket and DIN nut will attach the cap. 304 SS mat. Metric sizes available. Learn More$8.40
-
RUPTURE DISC-2IN TC (75 PSI) 75°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 75PSIG @ 75°F Learn More$600.00 -
RUPTURE DISC-1 1/2IN TC (130 PSI) 300°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 1 1/2IN TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 130.0 PSIG @ 300°F Learn More$1,368.00 -
RUPTURE DISC-2IN TC (88.3 PSI) 72°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 88.3 PSIG @ 72°F SR-H TYPE Learn More$400.00 -
RUPTURE DISC-2IN TC (25 PSI) 72°F (ASME) 316L EPDMThe rupture disc fits between 2IN TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Replace the disk every 5-6 years depending on the use of the tank to ensure superior performance. Learn More$689.00Out of stock -
CAP-DIN 100 METRIC-IMPERIAL (4IN) 304 (DIN 11851 UNION)The DIN cap is used to seal the end of a tube, fitting, or valve which has a DIN threaded ferrule. A gasket and DIN nut will attach the cap. 304 SS mat. Metric sizes available. Learn More$49.60
