Search results for: 'threaded 2 1/2'
- Related search terms
- 1/2" DIN check valve
- threaded
- threaded rod
-
TEE-BW 304 1IN SHORT POLButt Weld tees are a simplified manifold used to regulate fluid direction. Learn More$9.99 -
CLAMP-TC 304 5IN 13MHM SINGLE PINThe TC clamp is used to clamp two TC ferrules together. A TC gasket is installed between the ferrule for a complete seal. 304 Stainless Steel. Learn More$26.27 -
CAP-TC 304 5IN 16AMPThe TC cap is used to seal the end of a tube, fitting or valve which has a TC ferrule. A gasket and clamp attach the cap. 304 SS mat. Learn More$32.50 -
GASKET-TC 1IN SILICONE 40MPTri-Clamp Gaskets are seals made of FDA materials are designed to fit the grooves of Tri-Clamp Tube fittings used primarily in food processing lines, as well as in the pharmaceutical and biotech industries. Learn More$1.02
-
Hot
PRESSURE GAUGE 0-100 PSI 2.5IN DIAL, REAR MOUNT, 1/4IN MNPT CONNThe range of a pressure gauge should be approximately twice the operating pressure of the vessel. Learn More$24.00 -
GASKET-TC 1IN PTFETC gaskets are stocked in variety of materials. The gasket seats between two TC ferrules. Buna is the most common material used. Silicone or Teflon are used for higher temperature applications depending on customer preference. PTFE 40MP Learn More$3.69
-
SPRAYBALL-2.5IN X 1IN- TOP SPRAYSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn More$41.00 -
TRI-CLAMP FERRULE 304 1IN TC X 4.5IN LGThe Tri-Clamp (TC) Ferrule is one end of a three part connection. This is the most commonly used type of sanitary process pipe connection. Longer and shorter necks are available. 304 SS mat. Learn More$8.62
-
TRI-CLAMP FERRULE 304 1IN TC X 3IN LGThe Tri-Clamp (TC) Ferrule is one end of a three part connection. This is the most commonly used type of sanitary process pipe connection. Longer and shorter necks are available. 304 SS mat. Learn More$6.48 -
GASKET-MW 18IN SILICONE BLACK FULL FACEFull face gasket for 18" bubble (round) manway. This manway is side mounted. Learn More$172.00 -
GASKET-TC 1INTC gaskets are stocked in variety of materials. The gasket seats between two TC ferrules. Buna is the most common material used. Silicone or Teflon are used for higher temperature applications depending on customer preference. Learn More$0.49 -
GASKET-TC 1IN BUNA WHITETC gaskets are stocked in variety of materials. The gasket seats between two TC ferrules. Buna is the most common material used. Silicone or Teflon are used for higher temperature applications depending on customer preference. BUNA WHITE 40MP Learn More$0.50 -
FERRULE-DIN 100 IMPERIAL 4.0IN FEMALE LINER 304 DIN 11851 UNIONThe DIN ferrule is one side of a three piece DIN connection. Slip the DIN nut on the tubing before welding the ferrule in place. 304 SS mat. Learn More$17.60 -
FERRULE-DIN 25 IMPERIAL 1.0IN FEMALE LINER 304 DIN 11851 UNIONThe DIN ferrule is one side of a three piece DIN connection. Slip the DIN nut on the tubing before welding the ferrule in place. 304 SS mat. Learn More$9.25 -
Pressure GaugeThe range of a pressure gauge should be approximately twice the operating pressure of the vessel. ICC NW stocks 30 lb. Liquid filled gauges with 1/4 in. pipe thread connections. It is important to "burp" gauges periodically. Peel the black rubber stopper at the top of the valve back until pressure is released. Learn MoreAs low as $24.00 -
PRESSURE RELIEF VALVE, GUTH VENT, 0.9 LB, 3IN TC, (134-0105)The P.R.V. attaches to a 3IN TC vent. Valve relieves pressure as the fluid level rises while filling a tank Valve relieves vacuum as the fluid level drops while emptying a tank Seals under equal pressure Full body 316 stainless steel construction 1/4" FNPT connection for gas inlet, plug is included Vacuum break: , 0.1 PSI Pressure relief: 0.9 PSI Maximum temperature and pressure rating: 3 PSI @ 70°F Maximum flow rate: 500 GPM Learn More$312.00 -
SOLENOID VALVE 1IN 120VA brass Solenoid Valve is used to regulate coolant. The strength of brass is needed for the constant valve cycling. Learn More$429.68 -
NUT-DIN 75 METRIC-IMPERIAL 304 (DIN 11851 UNION)The DIN nut accompanies the plain DIN ferrule and is tightened with a DIN wrench. The nut serves the same function as a clamp in a TC connection. 304 SS mat. Learn More$29.68 -
NUT-DIN 50 METRIC-IMPERIAL 304 (DIN 11851 UNION)The DIN nut accompanies the plain DIN ferrule and is tightened with a DIN wrench. The nut serves the same function as a clamp in a TC connection. 304 SS mat. Metric sizes available. Learn More$33.60 -
NUT-DIN 25 METRIC-IMPERIAL 304 (DIN 11851 UNION)The DIN nut accompanies the plain DIN ferrule and is tightened with a DIN wrench. The nut serves the same function as a clamp in a TC connection. 304 SS mat. Metric sizes available. Learn More$12.30
