Search results for: 'manway gasket'A=0'
- Related search terms
- manway gaskets
- manway gasket bright tank
- manway gaskets silicone
-
CLAMP-TC 304 2.5IN 13MHM SINGLE PINThe TC clamp is used to clamp two TC ferrules together. A TC gasket is installed between the ferrule for a complete seal. 304 Stainless Steel. Learn More$4.28 -
CLAMP-TC 304 .5IN & .75IN 13MHM SINGLE PINThe TC clamp is used to clamp two TC ferrules together. A TC gasket is installed between the ferrule for a complete seal. 304 Stainless Steel. Learn More$3.81 -
Sanitary Hinged Lid PartsAvailable with sliding doors, removable doors, and CIP-able options as well as double half circle hatches with fixed or removable bridge. Learn MoreAs low as $3.50 -
ThermometerThermometer face is 2-1/2 in. diameter and has a 1/2 in. MNPT threaded connection. Temperature range reads from 0 to 250 deg. F (-20 to 120 deg.C). Learn MoreAs low as $33.00 -
Poly TC CapThe clear TC cap attaches to a TC ferrule for viewing. These caps are not designed to be used under pressure. Caution must be used in tightening the clamp as the cap can crack. Learn MoreAs low as $12.00 -
Ball ValvesThe stainless steel ball valve has female threaded pipe connections, and is a "full port" valve (the flow is not restricted). 316 SS mat. Learn MoreAs low as $48.75 -
TC 45° ElbowThe 45° elbow has TC connections on each end. TC elbows allow lines to be broken down for cleaning. Additional sizes and butt-weld elbows available. 304 or 316L SS mat. Learn MoreAs low as $9.42 -
Butterfly ValvesThe butterfly valve is used in process flow piping where fractional flow control is required. The valve has a stainless steel body with a silicon valve seat. TC connections shown. Other connections and butt-weld ends available on all butterfly valves. 304 SS mat. Learn MoreAs low as $120.92 -
P.A.M. Tree PartsThe P.A.M. Tree assembly groups the necessary fittings for tank pressure regulation together at the end of the vent extension line. The standard tree assembly consists of a pressure gauge, ball valve, and an open TC port. Does not include a P.R.V. Learn MoreAs low as $8.18 -
TC Eccentric ReducerEccentric reducers are used for tubing size transitions. The flat side allows complete drainage in horizontal piping. Custom reducers, additional sizes and butt-weld available. 304 SS mat. Learn MoreAs low as $25.25
-
SPRAYBALL-2.5IN X 1IN- BOTTOM SPRAY - 316LSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. DIA X 1IN DIA SLIP JOINT BOTTOM SPRAY PATTERN 316L Learn More$47.64 -
SPRAYBALL-2.5IN X 1IN- TOP SPRAYSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn More$41.00 -
Pressure GaugeThe range of a pressure gauge should be approximately twice the operating pressure of the vessel. ICC NW stocks 30 lb. Liquid filled gauges with 1/4 in. pipe thread connections. It is important to "burp" gauges periodically. Peel the black rubber stopper at the top of the valve back until pressure is released. Learn MoreAs low as $24.00 -
P.R.V.The P.R.V. are available for 2IN, 3IN and 4IN TC vent. Full 304 stainless steel body construction. Learn MoreAs low as $312.00 -
PIN, COTTER FOR SPRAYBALL-2.5IN DIA X 1IN DIA SLIP JOINTSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn More$3.50 -
COTTER PIN 2.5INSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn More$4.95 -
Hi-Low Level ControlThe hi-low level control is used to regulate wort receiver levels. Commonly used on both the brewpub open wort receiver and the enclosed airless grant. Wetted parts are 316 Stainless Steel. Learn MoreAs low as $272.27 -
Sani-SpinThe Sani-Spin is used much the same way as a C.I.P. sprayball. The advantage of the Sani-Spin is the force of it’s spinning action and the minimal volume it requires. For example, the optimum operating condition for a C.I.P. sprayball is 40 GPM @ 25 PSI; where as the Sani-Spin requires just 25 GPM @ 30 PSI. Learn MoreAs low as $618.00 -
(10) Spring Compression SSHeavy-duty 7ga outswing door and wing nuts swing free and clear of opening. Stainless steel wing nut assembly for extra strength with brass-lined wing nuts to prevent galling. Double cross arm for strong seal. Learn More$18.20 -
BRONZE FLANGED - SLEEVE BEARINGSleeve Bearing for: 1-arm rectangular mw 2 or 3-arm rectangular mw 20IN & 24IN top outswing mw Learn More$8.00
