Search results for: 'temp probe for tank net'nvOpzp; AND 1=1 OR (<'">iKO)),'

Parts for 18" Bubble (round) manway. This manway is side mounted and used on atmospheric tanks only Door plates are custom-made. These parts fit our #30804011804 (4IN Collar) and our #30804011806 (6IN Collar) models. Learn More

The Sani-Spin is used much the same way as a C.I.P. sprayball. The advantage of the Sani-Spin is the force of it’s spinning action and the minimal volume it requires. For example, the optimum operating condition for a C.I.P. sprayball is 40 GPM @ 25 PSI; where as the Sani-Spin requires just 25 GPM @ 30 PSI. Learn More

Parts for 16" x 21" Manway. Heavy-duty 7ga outswing door and wing nuts swing free and clear of opening. Stainless steel wing nut assembly for extra strength with brass-lined wing nuts to prevent galling. Double cross arm for strong seal. Learn More

Springs, Gaskets etc for P.R.V's Learn More

The P.R.V. attaches to a 2 IN TC vent or P.A.M. assembly. The valve is easy to take apart and clean. 15 lb. and 25 lb. pressure springs are available. Relief pressure can be adjusted down 5 lb. The valve will open at 0.089 lb. of vacumm. Full stainless steel body construction. Learn More

An AC drive, also known as an adjustable frequency drive (AFD), variable frequency drive (VFD), or inverter drive, is an electronic device used to control the speed and torque of an alternating current (AC) motor. It works by varying the frequency and voltage of the electrical power supplied to the motor, allowing for precise control over its operation. AC drives are commonly used in industrial and commercial applications to optimize energy consumption, improve process control, and extend the lifespan of motors by reducing wear and tear. They are essential components in machinery such as pumps, fans, conveyors, and compressors, where variable speed operation is required. AC drives offer benefits such as energy savings, smoother operation, and the ability to tailor motor performance to specific application requirements. Learn More

The low level sensor is an on/off float switch. The float should mount at the low level limit of a tank. Most commonly used in a hot liquor tank. Learn More

A rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 110.00 PSIG @ 200°F TYPE AXIUS SC Learn More

A rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 1 1/2IN TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 130.0 PSIG @ 300°F Learn More

A TC x FNPT will adapt a TC ferrule to male pipe fittings. One end is a TC, the other is female threaded pipe. 304 SS mat. Learn More

Eccentric reducers are used for tubing size transitions. The flat side allows complete drainage in horizontal piping. Custom reducers, additional sizes and butt-weld available. 304 SS mat. SIZE 2IN X 1IN Learn More

Tubes are designed for ICC NW varying capacity storage tanks. Please consult chart for correct size, questions please call (503) 468-6560. Our tube forumla changed in 2021. Learn More

The 45 deg. elbow has TC connections on each end. TC elbows allow lines to be broken down for cleaning. Additional sizes and butt-weld elbows available. 304 SS mat. Learn More

TC adapters are an economical alternative to a concentric reducer. This fitting is used to reduce the size in process piping where turbulence and complete drainage of the product is not a concern. 304 SS mat. Learn More

A TC x MNPT will adapt a TRI-CLAMP (TC) ferrule to female pipe fittings. One end is TRI-CLAMP (TC) and the other is male threaded pipe. 304 SS mat. Learn More

A TC x MNPT will adapt a TRI-CLAMP (TC) ferrule to female pipe fittings. One end is TRI-CLAMP (TC) and the other is male threaded pipe. 304 SS mat. Learn More

A TC x MNPT will adapt a TRI-CLAMP (TC) ferrule to female pipe fittings. One end is TRI-CLAMP (TC) and the other is male threaded pipe. 304 SS mat. Learn More

A TC x barb will adapt a TC ferrule to hose stock. When ordering specify the ID of the hose to be used. 304 SS mat. Learn More

A TC x barb will adapt a TC ferrule to hose stock. When ordering specify the ID of the hose to be used. 304 SS mat. Learn More

A TC x barb will adapt a TC ferrule to hose stock. When ordering specify the ID of the hose to be used. 304 SS mat. Learn More