Search results for: '4” gasket'
- Related search terms
- gasket-mw g'a=0'
- gasket-mw g'a=0'a=0'
- gasket-mw g'a=0'a=0',(;))
-
Hot
PRESSURE GAUGE 0-100 PSI 2.5IN DIAL, REAR MOUNT, 1/4IN MNPT CONNThe range of a pressure gauge should be approximately twice the operating pressure of the vessel. Learn More$24.00 -
Hot
CONTROLLER, FUJI, DIGITAL PXR4-SAY1-4VTA1Please be advised that the manufacturer has officially discontinued this product. Learn More$198.00 -
Parts for 16x22 Oval Grainout ManwayParts for 16" x 22" Oval Grainout Manway. Side mount. Used on atmospheric tanks only. Learn MoreAs low as $0.53 -
Fuji Temp & PartsThe Fuji controller receives information from the temperature sensor and sends open/close signals to the Heat Transfer Jacket solenoid valve. It can also operate direct fire Burners/Immersion Heaters/Etc. Learn MoreAs low as $198.00 -
Pressure GaugeThe range of a pressure gauge should be approximately twice the operating pressure of the vessel. ICC NW stocks 30 lb. Liquid filled gauges with 1/4 in. pipe thread connections. It is important to "burp" gauges periodically. Peel the black rubber stopper at the top of the valve back until pressure is released. Learn MoreAs low as $24.00 -
Tank LightThe tank light is used to illuminate the inside of a vessel while brewing or cleaning. It mounts to a 2 in. TC fitting. A standard 120 volt circuit and a 50 watt bulb are required. Learn MoreAs low as $25.00 -
STAINLESS STEEL WASHER 3/4IN ID FOR OVAL GRAINOUT AND BOTTOM CONE MANWAYSThis part can be used for the following manways: Oval-grainout, Bottom cone manways Learn More$0.53 -
NUT-NYLOCK 3/4INThis part can be used for the following manways: BTM CONE MANWAY, 18IN BUBBLE OUTSWING Learn More$1.12 -
TC 90° ElbowThe 90° elbow has TC connections on each end. TC elbows allow lines to be broken down for sanitizing. Butt-weld elbows available. 304 or 316L SS mat. Learn MoreAs low as $22.16 -
ELBOW-TC 304 4IN 90°The 90 deg. elbow has TC connections on each end. TC elbows allow lines to be broken down for sanitizing. Butt-weld elbows available. 304 SS mat. Learn More$62.96 -
ADAPTER-4IN TC CAP X 2IN TC FERRULE (CENTERED) 304TC adapters are an economical alternative to a concentric reducer. This fitting is used to reduce the size in process piping where turbulence and complete drainage of the product is not a concern. 304 SS mat. Learn More$17.00 -
ADAPTER-4IN TC CAP X 1.5IN TC FERRULE (CENTERED) 304TC adapters are an economical alternative to a concentric reducer. This fitting is used to reduce the size in process piping where turbulence and complete drainage of the product is not a concern. 304 SS mat. Learn More$29.40 -
GASKET-TC 1IN PTFETC gaskets are stocked in variety of materials. The gasket seats between two TC ferrules. Buna is the most common material used. Silicone or Teflon are used for higher temperature applications depending on customer preference. PTFE 40MP Learn More$3.69
-
GASKET-TC 1/2IN PTFETC gaskets are stocked in variety of materials. The gasket seats between two TC ferrules. Buna is the most common material used. Silicone or Teflon are used for higher temperature applications depending on customer preference. PTFE 40MP Learn More$1.02
-
GASKET-TC 3IN VITON BLACKThe gasket seats between two TC ferrules. Buna is the most common material used for temperature between -22F to +250F. Viton is commonly used for temperature up to 400F Silicone but not for low temperature. Teflon are used for higher temperature applications depending on customer preference. VITON BLACK 40MP Learn More$5.99 -
Hot
GASKET-TC 2.5IN VITON BLACKTC gaskets are stocked in variety of materials. The gasket seats between two TC ferrules. Buna is the most common material used. Silicone or Teflon are used for higher temperature applications depending on customer preference. VITON BLACK 40MP Learn More$8.25 -
Hot
GASKET-TC 2.5IN BUNA WHITETC gaskets are stocked in variety of materials. The gasket seats between two TC ferrules. Buna is the most common material used. Silicone or Teflon are used for higher temperature applications depending on customer preference. BUNA 40MP Learn More$0.28 -
GASKET-TC 2IN BUNATC gaskets are stocked in variety of materials. The gasket seats between two TC ferrules. Buna is the most common material used. Silicone or Teflon are used for higher temperature applications depending on customer preference. BUNA 40MP Learn More$0.18 -
GASKET-TC 1.5IN BUNA WHITETC gaskets are stocked in variety of materials. The gasket seats between two TC ferrules. Buna is the most common material used. Silicone or Teflon are used for higher temperature applications depending on customer preference. BUNA WHITE 40MP Learn More$0.24
