Search results for: '4” sight glass plexiglass'
- Related search terms
- sight glass lens 4 inch
- 4” o ring
- 4” gasket
-
GASKET-TC 4IN VITON BLACKTC gaskets are stocked in variety of materials. The gasket seats between two TC ferrules. Buna is the most common material used. Silicone or Teflon are used for higher temperature applications depending on customer preference. Learn More$4.46 -
Fuji Temp & PartsThe Fuji controller receives information from the temperature sensor and sends open/close signals to the Heat Transfer Jacket solenoid valve. It can also operate direct fire Burners/Immersion Heaters/Etc. Learn MoreAs low as $198.00 -
Pressure GaugeThe range of a pressure gauge should be approximately twice the operating pressure of the vessel. ICC NW stocks 30 lb. Liquid filled gauges with 1/4 in. pipe thread connections. It is important to "burp" gauges periodically. Peel the black rubber stopper at the top of the valve back until pressure is released. Learn MoreAs low as $24.00 -
DIN CapThe DIN cap is used to seal the end of a tube, fitting, or valve which has a DIN threaded ferrule. A gasket and DIN nut will attach the cap. 304 SS mat. Metric sizes available. Learn MoreAs low as $8.40 -
CAP-DIN 100 METRIC-IMPERIAL (4IN) 304 (DIN 11851 UNION)The DIN cap is used to seal the end of a tube, fitting, or valve which has a DIN threaded ferrule. A gasket and DIN nut will attach the cap. 304 SS mat. Metric sizes available. Learn More$49.60 -
Parts for 1-Arm Rectangular ManwayParts for 13" x 16" Manway. Heavy-duty 7ga construction. Rectangular Lid. Typically used for the ICC NW Econo-Tote Manway. Learn MoreAs low as $0.51 -
STAINLESS STEEL WASHER 3/4IN ID FOR OVAL GRAINOUT AND BOTTOM CONE MANWAYSThis part can be used for the following manways: Oval-grainout, Bottom cone manways Learn More$0.53 -
NUT-NYLOCK 3/4INThis part can be used for the following manways: BTM CONE MANWAY, 18IN BUBBLE OUTSWING Learn More$1.12 -
TC 90° ElbowThe 90° elbow has TC connections on each end. TC elbows allow lines to be broken down for sanitizing. Butt-weld elbows available. 304 or 316L SS mat. Learn MoreAs low as $22.16 -
ELBOW-TC 304 4IN 90°The 90 deg. elbow has TC connections on each end. TC elbows allow lines to be broken down for sanitizing. Butt-weld elbows available. 304 SS mat. Learn More$62.96 -
ADAPTER-4IN TC CAP X 2IN TC FERRULE (CENTERED) 304TC adapters are an economical alternative to a concentric reducer. This fitting is used to reduce the size in process piping where turbulence and complete drainage of the product is not a concern. 304 SS mat. Learn More$17.00 -
ADAPTER-4IN TC CAP X 1.5IN TC FERRULE (CENTERED) 304TC adapters are an economical alternative to a concentric reducer. This fitting is used to reduce the size in process piping where turbulence and complete drainage of the product is not a concern. 304 SS mat. Learn More$29.40 -
(11) Compression InsertThe 3-way level gauge valve will mount to a 1-1/2 in. TC at the base of a ICC NW level gauge system. This valve allows you to isolate the level gauge. 304 SS mat. The sight tube is translucent PFA Teflon. Make sure the tube insert is used at all tubing connections. Compression insert 1/2" for 5/8 for PTFE Tube .5IN OD for 5/8IN PTFE Tube Learn More$19.39 -
I-Line GasketsSanitary I-Line Gaskets. Available in Buna, EPDM, Teflon (PTFE) & Viton (FKM) Learn MoreAs low as $1.24 -
PowerFlex 525 0.75kW (1Hp) AC Drive #25B-D2P3N104Drive, PowerFlex 525, 380 - 480 Volt AC, 0.75 kW, 1 Horse Power, 2.3 Amp, Normal & Heavy Duty, Frame A, No Filter * Actual product may vary from image Learn More$265.00 -
PowerFlex 525 15kW (20Hp) AC Drive #25B-D030N104Drive, PowerFlex 525, 380 - 480 Volt AC, 15 kW, 20 Horse Power, Normal Duty, 11 kW, 15 Horse Power, Heavy Duty, 30 Amp, Frame D, No Filter * Actual product may vary from image Learn More$1,200.00 -
PowerFlex 525 11kW (15Hp) AC Drive #25B-D024N104Drive, PowerFlex 525, 380 - 480 Volt AC, 11 kW, 15 Horse Power, 24 Amp, Normal & Heavy Duty, Frame D, No Filter * Actual product may vary from image Learn More$1,100.00 -
GASKET-I-LINE 3IN PTFEBuna is the most common material used for temperature between -22F to +250F. Viton is commonly used for temperature up to 400F Silicone but not for low temperature. Teflon are used for higher temperature applications depending on customer preference. Learn More$1.24
-
GASKET-TC 1IN PTFETC gaskets are stocked in variety of materials. The gasket seats between two TC ferrules. Buna is the most common material used. Silicone or Teflon are used for higher temperature applications depending on customer preference. PTFE 40MP Learn More$3.69
