Search results for: 'VALVE-LEVEL GAUGE 1 1/2" TC CONNECTION, K10338LL458'nvOpzp; AND 1=1 OR (<'">iKO)),'

This part can be used for the following manways: Oval-grainout, Bottom cone manways Learn More

REDUCING TEE-BW 316L 2IN X 2IN X 1IN 7WR Learn More

Flange Gaskets. Available in Buna, EPDM, Teflon (PTFE) & Viton (FKM) Learn More

A TC x MNPT will adapt a TC (TRI-CLAMP) ferrule to female pipe fittings. One end is TC and the other is male threaded pipe. 304 SS mat. Learn More

REDUCER-BW 304 ECC 2 1/2IN X 2IN 32W Learn More

REDUCER-BW 304 CONC 2 1/2IN X 2IN 31W Learn More

REDUCER-BW 304 CONC 2IN X 1 1/2IN 31W Learn More

SEAL-AFM POLYSEAL 250-3.250 Learn More

Butt Weld tees are a simplified manifold used to regulate fluid direction. Learn More

The P.A.M. Tree assembly groups the necessary fittings for tank pressure regulation together at the end of the vent extension line. The standard tree assembly consists of a pressure gauge, ball valve, and an open TC port. Does not include a P.R.V. Learn More

An AC drive, also known as an adjustable frequency drive (AFD), variable frequency drive (VFD), or inverter drive, is an electronic device used to control the speed and torque of an alternating current (AC) motor. It works by varying the frequency and voltage of the electrical power supplied to the motor, allowing for precise control over its operation. AC drives are commonly used in industrial and commercial applications to optimize energy consumption, improve process control, and extend the lifespan of motors by reducing wear and tear. They are essential components in machinery such as pumps, fans, conveyors, and compressors, where variable speed operation is required. AC drives offer benefits such as energy savings, smoother operation, and the ability to tailor motor performance to specific application requirements. Learn More

The tee assembly is used to inject gas into the product. A hollow capped tube of cintered stainless is welded to a TC ferrule and clamped to a customized TC tee. This assembly includes a special tee, cintered stone, check valve, 3/8" hose barb, clamp and gasket. 304 SS mat. Learn More

The P.R.V. attaches to a 2 IN. TC vent or P.A.M. assembly. The valve is easy to take apart and clean. 15 lb. and 25 lb. pressure springs are available. Relief pressure can be adjusted down 5 lb. The valve will open at 0.089 lb. of vacumm. Full stainless steel body construction. Material: Silicone Learn More

The Tri-Clamp (TC) Ferrule is one end of a three part connection. This is the most commonly used type of sanitary process pipe connection. Ferrules have 1.125IN necks. Longer and shorter necks are available. 304 SS mat. Learn More

A TC x barb will adapt a TC ferrule to hose stock. When ordering specify the ID of the hose to be used. 304 SS mat. Learn More

A TC x barb will adapt a TC ferrule to hose stock. When ordering specify the ID of the hose to be used. 304 SS mat. Learn More

A TC x barb will adapt a TC ferrule to hose stock. When ordering specify the ID of the hose to be used. 304 SS mat. Learn More

Thermometer face is 3IN. diameter and has a 1/2 in. MNPT threaded connection. 12IN stem. Rear mounted. Temperature range reads from 0 to 250 deg. F Learn More

The in-line site glass is used for product viewing. Order includes replacement lense only. 2.5" wide x 4" long x 0.156" thick. Learn More

Thermometer face is 3IN. diameter and has a 1/2 in. MNPT threaded connection. 4IN stem. Rear mounted. Temperature range reads from 0 to 250 deg. F Learn More