Search results for: 'the%' AND 2*3*8=6*8 AND 'VvB9'!='VvB9%'

VALVE-BALL 1/2IN FNPT X 1/2IN FNPT 316 Learn More

REDUCING TEE-BW 316L 2IN X 2IN X 1IN 7WR Learn More

REDUCER-BW 304 ECC 2 1/2IN X 2IN 32W Learn More

REDUCER-BW 304 CONC 2 1/2IN X 2IN 31W Learn More

REDUCER-BW 304 CONC 2IN X 1 1/2IN 31W Learn More

The 45° elbow has TC connections on each end. TC elbows allow lines to be broken down for cleaning. Additional sizes and butt-weld elbows available. 304 or 316L SS mat. Learn More

Sprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn More

The Fuji controller receives information from the temperature sensor and sends open/close signals to the Heat Transfer Jacket solenoid valve. It can also operate direct fire Burners/Immersion Heaters/Etc. Learn More

An AC drive, also known as an adjustable frequency drive (AFD), variable frequency drive (VFD), or inverter drive, is an electronic device used to control the speed and torque of an alternating current (AC) motor. It works by varying the frequency and voltage of the electrical power supplied to the motor, allowing for precise control over its operation. AC drives are commonly used in industrial and commercial applications to optimize energy consumption, improve process control, and extend the lifespan of motors by reducing wear and tear. They are essential components in machinery such as pumps, fans, conveyors, and compressors, where variable speed operation is required. AC drives offer benefits such as energy savings, smoother operation, and the ability to tailor motor performance to specific application requirements. Learn More

Parts for 16" x 22" Oval Grainout Manway. Side mount. Used on atmospheric tanks only. Learn More

Parts for 13" x 16" Manway. Heavy-duty 7ga construction. Rectangular Lid. Typically used for the ICC NW Econo-Tote Manway. Learn More

SEAL-AFM POLYSEAL 250-3.250 Learn More

VENT-TCPV-4 304 4IN TC Learn More

SPRAYBALL- ROTARY IMPINGEMENT LARGE 304 Learn More

A TC x MNPT will adapt a TRI-CLAMP (TC) ferrule to female pipe fittings. One end is TRI-CLAMP (TC) ferrule and the other is male threaded pipe. 304 SS mat. Learn More

The TC cap is used to seal the end of a tube, fitting or valve which has a TC ferrule. A gasket and clamp attach the cap. 304 SS mat. Learn More

Concentric reducers are used for TC transitions in vertical tubing. Custom reducers, additional sizes and butt-weld available. 304 SS mat. Learn More

A TC x MNPT will adapt a TC (TRI-CLAMP) ferrule to female pipe fittings. One end is TC and the other is male threaded pipe. 304 SS mat. Learn More

A rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 1 1/2IN TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 130.0 PSIG @ 300°F Learn More

A rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 60.00 PSIG @ 200°F TYPE SR-H Learn More