Search results for: '1.5IN pyrex'
-
Sample Valve TCThe sample valve is designed to accommodate a CO2 test meter. Learn MoreAs low as $0.78 -
SAMPLE VALVE 1.5IN TC CONNECTORThe sample valve is designed to accommodate a CO2 test meter. Learn More$159.20
-
Poly TC CapThe clear TC cap attaches to a TC ferrule for viewing. These caps are not designed to be used under pressure. Caution must be used in tightening the clamp as the cap can crack. Learn MoreAs low as $12.00 -
CAP-TC 1.5IN - SG POLYThe clear TC cap attaches to a TC ferrule for viewing. These caps are not designed to be used under pressure. Caution must be used in tightening the clamp as the cap can crack. Learn More$12.00 -
StandpipeFor use in bottom-cone fermentation tanks, includes FDA silicone O-Ring Learn MoreAs low as $30.00 -
STANDPIPE - 1.5IN TCFor use in bottom-cone fermentation tanks, includes FDA silicone O-Ring Learn More$30.00 -
COTTER PIN 2.5INSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn More$4.95 -
VALVE-BALL FNPT .5IN 304The stainless steel ball valve has female threaded pipe connections, and is a "full port" valve (the flow is not restricted). 304 SS mat. FNPT Learn More$48.75 -
ELBOW-TC 304 1.5IN 90°The 90 deg. elbow has TC connections on each end. TC elbows allow lines to be broken down for sanitizing. Butt-weld elbows available. 304 SS mat. Learn More$23.55 -
TC Cap x TC Ferrule (offset)TC cap adapters are an economical alternative to an eccentric reducer. This fitting is used to reduce the size in process piping where turbulence and complete drainage of the product is not a concern. 304 SS mat. Learn MoreAs low as $19.99 -
GASKET-FLANGE FF 3IN X .125IN BUNA 150NODGASKET-FLANGE FF 3IN X .125IN BUNA 150NOD Learn More$7.88
-
GASKET-MW ARCHON/BOYER NATURAL RUBBER FOOD GRADE OVAL 14X17 (340x440) RATED TEMP -58*F / +194*FGASKET-MW ARCHON/BOYER NATURAL RUBBER FOOD GRADE OVAL 14X17 (340x440) RATED TEMP -58*F / +194*F Learn More$50.00 -
VALVE-SOLENOID REPLACEMENT COIL 120 V 1IN BRASSA brass Solenoid Valve is used to regulate coolant. The strength of brass is needed for the constant valve cycling. 120V Learn More$90.00 -
REDUCER, ECCENTRIC, 2IN X 1INEccentric reducers are used for tubing size transitions. The flat side allows complete drainage in horizontal piping. Custom reducers, additional sizes and butt-weld available. 304 SS mat. SIZE 2IN X 1IN Learn More$68.99
-
ELBOW-TC 316L 1IN 90°The 90 deg. elbow has TC connections on each end. TC elbows allow lines to be broken down for sanitizing. Butt-weld elbows available. 316 SS mat. Learn More$22.16 -
(1) PRESSURE RELIEF VALVE- E RING SHAE C-10105The P.R.V. attaches to a 2 IN TC vent or P.A.M. assembly. The valve is easy to take apart and clean. 15 lb. and 25 lb. pressure springs are available. Relief pressure can be adjusted down 5 lb. The valve will open at 0.089 lb. of vacumm. Full stainless steel body construction. Learn More$3.49 -
ELBOW-TC 304 1IN 90°The 90 deg. elbow has TC connections on each end. TC elbows allow lines to be broken down for sanitizing. Butt-weld elbows available. 304 SS mat. Learn More$29.34 -
ELBOW-TC 304 1IN 45°The 45 deg. elbow has TC connections on each end. TC elbows allow lines to be broken down for cleaning. Additional sizes and butt-weld elbows available. 304 SS mat. Learn More$30.25
