Search results for: 'manway gasket 120 bbl brite'
- Related search terms
- gasket mw G&H 18in epdm
- gasket-mw g'a=0') AND 7250=4306 AND (6887=6887
- gasket-mw g'a=0'')) AND 5404=5404 AND (('qiPE'='qiPE
-
Level Gauge Valve & PartsThe 3-way level gauge valve will mount to a 1-1/2 IN TC at the base of a ICC NW level gauge system. This valve allows you to isolate the level gauge. 304 SS mat. The sight tube is translucent PFA Teflon. Make sure the tube insert is used at all tubing connections. Learn MoreAs low as $1.50 -
GASKET-PRV 2IN 60 DUROThe P.R.V. attaches to a 2 IN. TC vent or P.A.M. assembly. The valve is easy to take apart and clean. 15 lb. and 25 lb. pressure springs are available. Relief pressure can be adjusted down 5 lb. The valve will open at 0.089 lb. of vacumm. Full stainless steel body construction. Material: Silicone Learn More$3.95 -
Parts for 18x22 Oval GrainoutParts for 18" x 22" Oval Grainout Manway. Side mount. Used on atmospheric tanks only. 304 SS. Learn MoreAs low as $4.80 -
DIN CapThe DIN cap is used to seal the end of a tube, fitting, or valve which has a DIN threaded ferrule. A gasket and DIN nut will attach the cap. 304 SS mat. Metric sizes available. Learn MoreAs low as $8.40 -
(3) KNUCKLE BLOCK ASSEMBLYSide mount. For 18IN bubble outswing manway and 18x22 and 16x22 oval grainout manway. Will fit 18x22IN and 16x22IN oval grainout manway 18IN bubble manway Learn More$231.89 -
Rupture DiskA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. Learn MoreAs low as $17.60 -
TC ClampThe TC (Tri-Clamp) is used to clamp two TC ferrules together. A TC gasket (sold separately) is installed between the ferrules for a complete seal. 304 stainless steel material. Learn MoreAs low as $3.81 -
TC CapThe TC cap is used to seal the end of a tube, fitting or valve which has a TC ferrule. A gasket and clamp attach the cap. 304 SS mat. Learn MoreAs low as $3.72 -
ThermometerThermometer face is 2-1/2 in. diameter and has a 1/2 in. MNPT threaded connection. Temperature range reads from 0 to 250 deg. F (-20 to 120 deg.C). Learn MoreAs low as $33.00 -
Tank LightThe tank light is used to illuminate the inside of a vessel while brewing or cleaning. It mounts to a 2 in. TC fitting. A standard 120 volt circuit and a 50 watt bulb are required. Learn MoreAs low as $25.00 -
Wingnut with Brass insertWingnut fits the following manways: 1-arm rectangular 2 or 3-arm rectangular This does NOT FIT the 16x22 manways. Learn More$165.39 -
Temperature PortThe TC cap is used to seal the end of a tube, fitting or valve which has a TC ferrule. A gasket and clamp attach the cap. 304 SS mat. Learn MoreAs low as $3.72 -
O-RING-BUNA 18.25IN ID X .375IN THK (OLD SKU NUMBER 10450840/10450850)Gasket (O-Ring) for Bottom Cone Manway. Material: Buna Learn More$73.77 -
Oxy Carb Tee AssemblyThe tee assembly is used to inject gas into the product. A hollow capped tube of cintered stainless is welded to a TC ferrule and clamped to a customized TC tee. This assembly includes a special tee, cintered stone, check valve, 3/8" hose barb, clamp and gasket. 304 SS mat. Learn MoreAs low as $524.00 -
SCREW CAP 4.5INThis part can be used for the following manways: 18IN BUBBLE OUTSWING Learn More$3.59 -
(6) Clevis PinClevis Pin secures cross arm to hinges. It fits 20IN and 24IN Top outswing manway. 1/2IN DIA X 1 7/8IN W/10-32 SCREW END Learn More$23.00
-
CROSS ARM ASS'Y-16X22 IN/OUTSWING FLUSH MOUNTCROSS ARM ASS'Y-16X22 IN/OUTSWING FLUSH MOUNT MANWAY Learn More$270.00 -
WINGNUT STUD 1/2 INWill fit the following manways: 1-arm rectangular 13 x 16 2 and 3 arm rectangular 16 x 21 top outswing manway 20 & 24 inch Learn More$37.00
