Search results for: 'tank-net-pl-1'
-
TRI-CLAMP (TC) ADAPTER 2IN x 0.25IN MNPTA TC x MNPT will adapt a TRI-CLAMP (TC) ferrule to female pipe fittings. One end is TRI-CLAMP (TC) and the other is male threaded pipe. 304 SS mat. Learn More$20.00 -
TRI-CLAMP (TC) ADAPTER 1.5IN x .75IN MNPTA TC x MNPT will adapt a TRI-CLAMP (TC) ferrule to female pipe fittings. One end is TRI-CLAMP (TC) and the other is male threaded pipe. 304 SS mat. Learn More$13.75 -
P.R.V.The P.R.V. are available for 2IN, 3IN and 4IN TC vent. Full 304 stainless steel body construction. Learn MoreAs low as $312.00 -
PRESSURE RELIEF VALVE, GUTH VENT, 0.9 LB, 3IN TC, (134-0105)The P.R.V. attaches to a 3IN TC vent. Valve relieves pressure as the fluid level rises while filling a tank Valve relieves vacuum as the fluid level drops while emptying a tank Seals under equal pressure Full body 316 stainless steel construction 1/4" FNPT connection for gas inlet, plug is included Vacuum break: , 0.1 PSI Pressure relief: 0.9 PSI Maximum temperature and pressure rating: 3 PSI @ 70°F Maximum flow rate: 500 GPM Learn More$312.00 -
Hot
RUPTURE DISK-2IN TC (110 PSI) 200°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 110.00 PSIG @ 200°F TYPE AXIUS SC Learn More$400.00 -
RUPTURE DISC-1 1/2IN TC (130 PSI) 300°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 1 1/2IN TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 130.0 PSIG @ 300°F Learn More$1,368.00 -
Parts for 18" Bubble (Round) Outswing ManwayParts for 18" Bubble (round) manway. This manway is side mounted and used on atmospheric tanks only Door plates are custom-made. These parts fit our #30804011804 (4IN Collar) and our #30804011806 (6IN Collar) models. Learn MoreAs low as $1.12 -
GASKET-MW 18IN OR 16X22 EPDM BLACK 50A DURO RIBBEDSide mount door swings clear of work area. Pressure of liquid inside the tank provides a positive seal. Can be used for 18IN round or 16x22 (Shadowless/Flushmount) manway. Learn More$152.00 -
SPRAYBALL-2.5IN X 1IN- BOTTOM SPRAY - 316LSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. DIA X 1IN DIA SLIP JOINT BOTTOM SPRAY PATTERN 316L Learn More$47.64 -
Parts for 18x22 Oval GrainoutParts for 18" x 22" Oval Grainout Manway. Side mount. Used on atmospheric tanks only. 304 SS. Learn MoreAs low as $4.80 -
GASKET-MW 18IN RND OR 16X22 SILICONE BLACK 50 DURO RIBBEDSide mount door swings clear of work area. Pressure of liquid inside the tank provides a positive seal. Can be used for 18IN round or 16x22 (Shadowless/Flushmount) manway. Learn More$120.00Out of stock -
Parts for Bottom Cone ManwayParts for Bottom Cone manway for fermentation tanks. Learn MoreAs low as $0.53 -
Low Level SensorThe low level sensor is an on/off float switch. The float should mount at the low level limit of a tank. Most commonly used in a hot liquor tank. Learn MoreAs low as $154.00 -
SPRAYBALL-2.5IN X 1IN- TOP SPRAYSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn More$41.00 -
PIN, COTTER FOR SPRAYBALL-2.5IN DIA X 1IN DIA SLIP JOINTSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn More$3.50 -
NUT-DIN 32 METRIC-IMPERIAL 304 (DIN 11851 UNION)The DIN nut accompanies the plain DIN ferrule and is tightened with a DIN wrench. The nut serves the same function as a clamp in a TC connection. 304 SS mat. Metric sizes available. Learn More$24.58
-
NUT-DIN 80 METRIC-IMPERIAL 304 (DIN 11851 UNION)The DIN nut accompanies the plain DIN ferrule and is tightened with a DIN wrench. The nut serves the same function as a clamp in a TC connection. 304 SS mat. Metric sizes available. Learn More$37.65
-
NUT-DIN 20 METRIC-IMPERIAL 304 DIN 11851 UNIONThe DIN nut accompanies the plain DIN ferrule and is tightened with a DIN wrench. The nut serves the same function as a clamp in a TC connection. 304 SS mat. Metric sizes available. Learn More$13.54
-
FERRULE-DIN 32 IMPERIAL 1.25IN FEMALE LINER 304 DIN 11851 UNIONThe DIN ferrule is one side of a three piece DIN connection. Slip the DIN nut on the tubing before welding the ferrule in place. 304 SS mat. Learn More$8.95
-
FERRULE-DIN 100 IMPERIAL 4.0IN FEMALE LINER 304 DIN 11851 UNIONThe DIN ferrule is one side of a three piece DIN connection. Slip the DIN nut on the tubing before welding the ferrule in place. 304 SS mat. Learn More$17.60
