Search results for: 'tank door wing nut and brass screw'
- Related search terms
- tank gasket
- tank gasket 18"
- tank Door gasket
-
FUJI CONTROLLER PXR4 DIGITALThe Fuji controller receives information from the temperature sensor and sends open/close signals to the Heat Transfer Jacket solenoid valve. It can also operate direct fire Burners/Immersion Heaters/Etc. Learn More$350.00 -
TRI-CLAMP (TC) ADAPTER 1.5IN x .5IN MNPTA TC x MNPT will adapt a TRI-CLAMP (TC) ferrule to female pipe fittings. One end is TRI-CLAMP (TC) and the other is male threaded pipe. 304 SS mat. Learn More$15.37 -
THERMOMETER-DIAL 3IN X 1/2IN MNPT, 4IN STEM, REAR MNT. 0-250 DEG FThermometer face is 3IN. diameter and has a 1/2 in. MNPT threaded connection. 4IN stem. Rear mounted. Temperature range reads from 0 to 250 deg. F Learn More$33.00 -
TRI-CLAMP FERRULE 304 2IN X 1.125IN LGThe Tri-Clamp (TC) Ferrule is one end of a three part connection. This is the most commonly used type of sanitary process pipe connection. Ferrules have 1.125IN necks. Longer and shorter necks are available. 304 SS mat. Learn More$5.00 -
TRI-CLAMP FERRULE 304 1.5IN X 1.125IN LGThe Tri-Clamp (TC) Ferrule is one end of a three part connection. This is the most commonly used type of sanitary process pipe connection. Ferrules have 1.125IN necks. Longer and shorter necks are available. 304 SS mat. Learn More$4.50 -
TRI-CLAMP FERRULE 304 1IN X 1.125IN LGThe Tri-Clamp (TC) Ferrule is one end of a three part connection. This is the most commonly used type of sanitary process pipe connection. Ferrules have 1.125IN necks. Longer and shorter necks are available. 304 SS mat. Learn More$5.00 -
TRI-CLAMP FERRULE 304 .5IN X 1.125IN LGThe Tri-Clamp (TC) Ferrule is one end of a three part connection. This is the most commonly used type of sanitary process pipe connection. Ferrules have 1.125IN necks. Longer and shorter necks are available. 304 SS mat. Learn More$13.50 -
Spring (only) 15lb for P.R.VThis spring is for a P.R. Valve. P.R. Valve SKU is SKU707040012 This spring is for a 15LB P.R.V. which attaches to a 2 in. TC vent or P.A.M. assembly. The valve is easy to take apart and clean. Learn More$27.60 -
Gaskets for Sanitary Pressure Outswing ManwayGasket will fit Top Outswing Manways. They are available in Buna, Viton, Silicone and EPDM Learn MoreAs low as $95.00 -
CLEVIS PIN .75 x 2.175Use a clevis pin as part of a clevis fastener. When threaded through the prongs of a tang and secured with a cotter pin, this fastening system allows movement along one axis while restricting it along the other. The clevis pin is used on the following ICC NW manways - 16X22 Shroud / Flushmount. Learn More$41.97 -
KNUCKLE BLOCK ASS'Y-16X22 MANWAY - FITS 4IN SHROUD / FLUSHMOUNT / SHADOWLESSKnuckle Block Assembly - Fits a 16X22 MANWAY, with a 4IN shroud and shadowless (flushmount) in|outswing manway Learn More$295.00 -
In-Line Sight Glass GasketThe in-line site glass is used for product viewing. The site glass has a TC ferrule on each end. The clear portion is either Pyrex or glass. One end unscrews to replace lens and gaskets. Learn MoreAs low as $2.50 -
Hot
CONTROL HI-LOW 2-LEVEL 15 1/2" LG SSThe hi-low level control is used to regulate wort receiver levels. Commonly used on both the brewpub open wort receiver and the enclosed airless grant. Wetted parts are 316 Stainless Steel. Learn More$272.27 -
Sani-Spin Sprayball with 1IN Slip JointThe Sani-Spin is used much the same way as a C.I.P. sprayball. The advantage of the Sani-Spin is the force of it’s spinning action and the minimal volume it requires. For example, the optimum operating condition for a C.I.P. sprayball is 40 GPM @ 25 PSI; where as the Sani-Spin requires just 25 GPM @ 30 PSI. Learn More$618.00 -
Butterfly Valve w/ Micro Metric Handle TC 2INThe multi-position butterfly valve is used in process flow piping where fractional flow control is required. The valve has a stainless steel body with a silicon valve seat. TC connections shown. Other connections and butt-weld ends available on all butterfly valves. 304 SS mat. Learn More$270.90 -
Butterfly Valve w Micro Metric Handle TC 1.5 INThe multi-position butterfly valve is used in process flow piping where fractional flow control is required. The valve has a stainless steel body with a silicon valve seat. TC connections shown. Other connections and butt-weld ends available on all butterfly valves. 304 SS mat. Learn More$254.54 -
VALVE-BALL FNPT .5IN 304The stainless steel ball valve has female threaded pipe connections, and is a "full port" valve (the flow is not restricted). 304 SS mat. FNPT Learn More$48.75 -
TEE-TC 304 2IN CONN 7MPThe TC has three TC ferrules for multi-purpose application. Custom branch sizes and butt-weld tees available. 304 SS mat. Learn More$38.40 -
REDUCER, ECCENTRIC 3IN X 2INEccentric reducers are used for tubing size transitions. The flat side allows complete drainage in horizontal piping. Custom reducers, additional sizes and butt-weld available. 304 SS mat. SIZE 3IN X 2IN Learn More$25.25
-
REDUCER, ECCENTRIC, 2IN X 1INEccentric reducers are used for tubing size transitions. The flat side allows complete drainage in horizontal piping. Custom reducers, additional sizes and butt-weld available. 304 SS mat. SIZE 2IN X 1IN Learn More$68.99
