Search results for: 'valve seat 1.5in piton definox'
- Related search terms
- valve seals
- valve level gauge
- VALVE-SEAT SILICONE 1 1/2IN
-
GASKET-TC 1.5IN BUNA 40MPBuna gaskets are made from a food grade, 3A approved material with good compression set characteristics, but have a limited temperature range (-30°F - 200°F) which precludes their use in many applications, primarily steam Learn More$0.55 -
GASKET-TC 1.5IN SILICONE 40MPTri-Clamp Gaskets are seals made of FDA materials are designed to fit the grooves of Tri-Clamp Tube fittings used primarily in food processing lines, as well as in the pharmaceutical and biotech industries. Learn More$3.78 -
TRI-CLAMP FERRULE 304 2.5IN TC X 3IN LGThe Tri-Clamp (TC) Ferrule is one end of a three part connection. This is the most commonly used type of sanitary process pipe connection. Longer and shorter necks are available. 304 SS mat. Learn More$14.81
-
Poly TC CapThe clear TC cap attaches to a TC ferrule for viewing. These caps are not designed to be used under pressure. Caution must be used in tightening the clamp as the cap can crack. Learn MoreAs low as $12.00 -
CAP-TC 1.5IN - SG POLYThe clear TC cap attaches to a TC ferrule for viewing. These caps are not designed to be used under pressure. Caution must be used in tightening the clamp as the cap can crack. Learn More$12.00 -
StandpipeFor use in bottom-cone fermentation tanks, includes FDA silicone O-Ring Learn MoreAs low as $30.00 -
STANDPIPE - 1.5IN TCFor use in bottom-cone fermentation tanks, includes FDA silicone O-Ring Learn More$30.00 -
COTTER PIN 2.5INSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn More$4.95 -
In-Line Sight Glass GasketThe in-line site glass is used for product viewing. The site glass has a TC ferrule on each end. The clear portion is either Pyrex or glass. One end unscrews to replace lens and gaskets. Learn MoreAs low as $2.50
-
ELBOW-TC 304 1.5IN 90°The 90 deg. elbow has TC connections on each end. TC elbows allow lines to be broken down for sanitizing. Butt-weld elbows available. 304 SS mat. Learn More$23.55 -
TC Cap x TC Ferrule (offset)TC cap adapters are an economical alternative to an eccentric reducer. This fitting is used to reduce the size in process piping where turbulence and complete drainage of the product is not a concern. 304 SS mat. Learn MoreAs low as $19.99 -
VALVE-BALL TC X TC 2IN 304Stainless steel one-way ball valves have lockable handles to prevent tampering and are used to control flow in a closed pipe system Learn More$221.60
-
VALVE-BALL 316L TC X TC 1 INThe stainless steel ball valve has TC connections. 316 SS mat. Learn More$82.00 -
VALVE-CHECK 3/8IN MNPT X 3/8IN MNPT 10 PSI 316A check valve with a ten pound spring is used with carbonation stone assemblies to prevent product back-flow. Check valves are available with male or female pipe thread connections. Learn More$138.00 -
GASKET-PRV 2IN 60 DUROThe P.R.V. attaches to a 2 IN. TC vent or P.A.M. assembly. The valve is easy to take apart and clean. 15 lb. and 25 lb. pressure springs are available. Relief pressure can be adjusted down 5 lb. The valve will open at 0.089 lb. of vacumm. Full stainless steel body construction. Material: Silicone Learn More$3.95
