Search results for: 'gaskets for tank doors''
- Related search terms
- gaskets manway
- gaskets for tank doors
- tank door wing nut
-
Tank LightThe tank light is used to illuminate the inside of a vessel while brewing or cleaning. It mounts to a 2 in. TC fitting. A standard 120 volt circuit and a 50 watt bulb are required. Learn MoreAs low as $25.00 -
I-Line GasketsSanitary I-Line Gaskets. Available in Buna, EPDM, Teflon (PTFE) & Viton (FKM) Learn MoreAs low as $1.24 -
Gaskets - Top OutswingTop mount inspection manway accommodates right, left, and top hinge locations. Cool-to-touch (outdoors) high impact PVC grip knob. Hygienic dome lid and narrow cross arms allow complete wash-down, no puddles. 360 degree locations. Learn MoreAs low as $175.00 -
Gaskets for Sanitary Pressure Outswing ManwayGasket will fit Top Outswing Manways. They are available in Buna, Viton, Silicone and EPDM Learn MoreAs low as $95.00 -
Temperature ControllerIs temperature control specifically designed for use in wineries and breweries. Learn MoreAs low as $96.00 -
Sanitary Hinged Lid PartsAvailable with sliding doors, removable doors, and CIP-able options as well as double half circle hatches with fixed or removable bridge. Learn MoreAs low as $3.50 -
TC GasketThe gasket seats between two TC ferrules. Buna is the most common material used for temperature between -22F to +250F. Viton is commonly used for temperature up to 400F Silicone but not for low temperature. Teflon are used for higher temperature applications depending on customer preference. Learn MoreAs low as $0.18 -
Parts for Shadowless Inswing/Outswing ManwayParts for 16" x 22" Shadowless (Flushmount) Inswing/Outswing Manway. Completely Flush interior. No cleaning shadow. Side mount. Standard is 304 SS. Call if 316L is required. Door plates are custom-made. Call for price and lead time. Learn MoreAs low as $41.97 -
HINGE ARM ASS'Y-16X22 IN/OUTSWING FLUSHMOUNT MW NON-INSLT'D TANKHINGE ARM ASS'Y-16X22 IN/OUTSWING FLUSHMOUNT MW NON-INSLT'D TANK Learn More$215.00 -
Rupture DiskA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. Learn MoreAs low as $17.60 -
DIN GasketDIN gaskets fit into a threaded DIN ferrule to complete the seal. Learn MoreAs low as $0.53 -
Sani-SpinThe Sani-Spin is used much the same way as a C.I.P. sprayball. The advantage of the Sani-Spin is the force of it’s spinning action and the minimal volume it requires. For example, the optimum operating condition for a C.I.P. sprayball is 40 GPM @ 25 PSI; where as the Sani-Spin requires just 25 GPM @ 30 PSI. Learn MoreAs low as $618.00 -
Sprayballs & PartsSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn MoreAs low as $3.50 -
Low Level SensorThe low level sensor is an on/off float switch. The float should mount at the low level limit of a tank. Most commonly used in a hot liquor tank. Learn MoreAs low as $154.00 -
Floating Lid TubeTubes are designed for ICC NW varying capacity storage tanks. Please consult chart for correct size, questions please call (503) 468-6560. Our tube forumla changed in 2021. Learn MoreAs low as $0.64 -
P.A.M. Tree PartsThe P.A.M. Tree assembly groups the necessary fittings for tank pressure regulation together at the end of the vent extension line. The standard tree assembly consists of a pressure gauge, ball valve, and an open TC port. Does not include a P.R.V. Learn MoreAs low as $8.18 -
Sani-Spin Sprayball with 1IN Slip JointThe Sani-Spin is used much the same way as a C.I.P. sprayball. The advantage of the Sani-Spin is the force of it’s spinning action and the minimal volume it requires. For example, the optimum operating condition for a C.I.P. sprayball is 40 GPM @ 25 PSI; where as the Sani-Spin requires just 25 GPM @ 30 PSI. Learn More$618.00
