Search results for: 'tank drain screw valve'
- Related search terms
- valve seat 1.5in piton definox
- VALVE-SEAT SILICONE 1 1/2IN'
- VALVE-LEVEL GAUGE 1 1/2" TC CONNECTION, K10338LL458'nvOpzp; AND 1=1 OR (<'">iKO)),
-
Valve SeatsValve seats seal the valve body against the disk to stop flow. Learn MoreAs low as $12.65 -
Level Gauge Valve & PartsThe 3-way level gauge valve will mount to a 1-1/2 IN TC at the base of a ICC NW level gauge system. This valve allows you to isolate the level gauge. 304 SS mat. The sight tube is translucent PFA Teflon. Make sure the tube insert is used at all tubing connections. Learn MoreAs low as $1.50 -
Butterfly ValvesThe butterfly valve is used in process flow piping where fractional flow control is required. The valve has a stainless steel body with a silicon valve seat. TC connections shown. Other connections and butt-weld ends available on all butterfly valves. 304 SS mat. Learn MoreAs low as $120.92 -
Ball ValvesThe stainless steel ball valve has female threaded pipe connections, and is a "full port" valve (the flow is not restricted). 316 SS mat. Learn MoreAs low as $48.75 -
Sample Valve TCThe sample valve is designed to accommodate a CO2 test meter. Learn MoreAs low as $0.78 -
Solenoid ValveA brass Solenoid Valve is used to regulate coolant. The strength of brass is needed for the constant valve cycling. Learn MoreAs low as $52.81 -
Sample Valve MNPTThe sample valve is designed to accommodate a CO2 test meter. Learn MoreAs low as $0.78
-
Tank LightThe tank light is used to illuminate the inside of a vessel while brewing or cleaning. It mounts to a 2 in. TC fitting. A standard 120 volt circuit and a 50 watt bulb are required. Learn MoreAs low as $25.00 -
Replacement Coil - Solenoid ValveA brass Solenoid Valve is used to regulate coolant. The strength of brass is needed for the constant valve cycling. Learn MoreAs low as $56.70 -
Parts for Bottom Cone ManwayParts for Bottom Cone manway for fermentation tanks. Learn MoreAs low as $0.53 -
Parts for 18" Bubble (Round) Outswing ManwayParts for 18" Bubble (round) manway. This manway is side mounted and used on atmospheric tanks only Door plates are custom-made. These parts fit our #30804011804 (4IN Collar) and our #30804011806 (6IN Collar) models. Learn MoreAs low as $1.12 -
Temperature ControllerIs temperature control specifically designed for use in wineries and breweries. Learn MoreAs low as $96.00 -
SCREW CAP 4.5INThis part can be used for the following manways: 18IN BUBBLE OUTSWING Learn More$3.59
-
Parts for 1-Arm Rectangular ManwayParts for 13" x 16" Manway. Heavy-duty 7ga construction. Rectangular Lid. Typically used for the ICC NW Econo-Tote Manway. Learn MoreAs low as $0.51 -
Screw Cap Hex 1/2INThis part can be used for the following manways: BTM CONE MANWAY Learn More$0.70 -
Parts for Shadowless Inswing/Outswing ManwayParts for 16" x 22" Shadowless (Flushmount) Inswing/Outswing Manway. Completely Flush interior. No cleaning shadow. Side mount. Standard is 304 SS. Call if 316L is required. Door plates are custom-made. Call for price and lead time. Learn MoreAs low as $41.97 -
HINGE ARM ASS'Y-16X22 IN/OUTSWING FLUSHMOUNT MW NON-INSLT'D TANKHINGE ARM ASS'Y-16X22 IN/OUTSWING FLUSHMOUNT MW NON-INSLT'D TANK Learn More$215.00
