Search results for: '1/2" DIN check valve'
- Related search terms
- valve seat
- Din to TC adapter
- VALVE-LEVEL GAUGE 1 1/2" TC CONNECTION, K10338LL458'
-
RUPTURE DISC-2IN TC (88.3 PSI) 72°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 88.3 PSIG @ 72°F SR-H TYPE Learn More$400.00 -
Hot
GASKET-TC 2IN EPDMTC gaskets are stocked in variety of materials. The gasket seats between two TC ferrules. Buna is the most common material used. Silicone or Teflon are used for higher temperature applications depending on customer preference. Learn More$0.57 -
GASKET-TC 2IN BUNATC gaskets are stocked in variety of materials. The gasket seats between two TC ferrules. Buna is the most common material used. Silicone or Teflon are used for higher temperature applications depending on customer preference. Learn More$1.08 -
GASKET-TC 2IN BUNATC gaskets are stocked in variety of materials. The gasket seats between two TC ferrules. Buna is the most common material used. Silicone or Teflon are used for higher temperature applications depending on customer preference. BUNA 40MP Learn More$0.18 -
GASKET-TC 1 1/2IN PTFETC gaskets are stocked in variety of materials. The gasket seats between two TC ferrules. Buna is the most common material used. Silicone or Teflon are used for higher temperature applications depending on customer preference. PTFE 40MP Learn More$3.24 -
Poly TC CapThe clear TC cap attaches to a TC ferrule for viewing. These caps are not designed to be used under pressure. Caution must be used in tightening the clamp as the cap can crack. Learn MoreAs low as $12.00 -
CAP-TC 2IN - SG POLYThe clear TC cap attaches to a TC ferrule for viewing. These caps are not designed to be used under pressure. Caution must be used in tightening the clamp as the cap can crack. Learn More$16.50 -
TC/Gas Fitting AssemblyThe TC x Gas Fitting is used to add a CO2-Nitrogen mix to your serving tank. We can also add a carbonation "stone" to the TC fitting and use the assembly to carbonate your beer. Learn MoreAs low as $45.65 -
TEE-TC 304 2IN CONN 7MPThe TC has three TC ferrules for multi-purpose application. Custom branch sizes and butt-weld tees available. 304 SS mat. Learn More$38.40 -
Screw Cap Hex 1/2INThis part can be used for the following manways: BTM CONE MANWAY Learn More$0.70 -
CROSS ARM ASS'Y-10IN TOP OUTSWING MANWAYDesigned for the flat top 10" manway. Manway designed to not hold pressure. Learn More$164.59 -
WINGNUT FOR 18IN BOTTOM CONE MANWAY 304 (old style)This part can be used for the following manways: BTM CONE MANWAY Learn More$108.89 -
TEE-BW 304 1IN SHORT POLButt Weld tees are a simplified manifold used to regulate fluid direction. Learn More$9.99 -
CLAMP-TC 304 5IN 13MHM SINGLE PINThe TC clamp is used to clamp two TC ferrules together. A TC gasket is installed between the ferrule for a complete seal. 304 Stainless Steel. Learn More$26.27 -
GASKET-TC 1IN SILICONE 40MPTri-Clamp Gaskets are seals made of FDA materials are designed to fit the grooves of Tri-Clamp Tube fittings used primarily in food processing lines, as well as in the pharmaceutical and biotech industries. Learn More$1.02
-
Hot
PRESSURE GAUGE 0-100 PSI 2.5IN DIAL, REAR MOUNT, 1/4IN MNPT CONNThe range of a pressure gauge should be approximately twice the operating pressure of the vessel. Learn More$24.00 -
GASKET-TC 1IN PTFETC gaskets are stocked in variety of materials. The gasket seats between two TC ferrules. Buna is the most common material used. Silicone or Teflon are used for higher temperature applications depending on customer preference. PTFE 40MP Learn More$3.69
