Search results for: 'tank drain screw valve'
- Related search terms
- VALVE-SEAT SILICONE 1 1/2IN'
- VALVE-LEVEL GAUGE 1 1/2" TC CONNECTION, K10338LL458'
- VALVE-LEVEL GAUGE 1 1/2" TC CONNECTION, K10338LL458'nvOpzp; AND 1=1 OR (<'">iKO)),
-
Butterfly Valve Seat 1.5 Silicone for H&H ValvesValve Seat for H&H Butterfly Valves 1.5IN - Fit HH30415 Learn More$15.00 -
SAMPLE VALVE 1.5IN TC CONNECTORThe sample valve is designed to accommodate a CO2 test meter. Learn More$159.20 -
Sample Valve 0.375INThe sample valve is designed to accommodate a CO2 test meter. Learn More$118.50
-
VALVE-CHECK 3/8IN MNPT X 3/8IN MNPT 10 PSI 316A check valve with a ten pound spring is used with carbonation stone assemblies to prevent product back-flow. Check valves are available with male or female pipe thread connections. Learn More$138.00 -
TC Eccentric ReducerEccentric reducers are used for tubing size transitions. The flat side allows complete drainage in horizontal piping. Custom reducers, additional sizes and butt-weld available. 304 SS mat. Learn MoreAs low as $25.25
-
Sprayballs & PartsSprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn MoreAs low as $3.50 -
P.A.M. Tree PartsThe P.A.M. Tree assembly groups the necessary fittings for tank pressure regulation together at the end of the vent extension line. The standard tree assembly consists of a pressure gauge, ball valve, and an open TC port. Does not include a P.R.V. Learn MoreAs low as $8.18 -
Low Level SensorThe low level sensor is an on/off float switch. The float should mount at the low level limit of a tank. Most commonly used in a hot liquor tank. Learn MoreAs low as $154.00 -
DIN CapThe DIN cap is used to seal the end of a tube, fitting, or valve which has a DIN threaded ferrule. A gasket and DIN nut will attach the cap. 304 SS mat. Metric sizes available. Learn MoreAs low as $8.40 -
TC Cap x TC Ferrule (offset)TC cap adapters are an economical alternative to an eccentric reducer. This fitting is used to reduce the size in process piping where turbulence and complete drainage of the product is not a concern. 304 SS mat. Learn MoreAs low as $19.99 -
RUPTURE DISC-2IN TC (60 PSI) 200°F (ASME) PTFE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 60.00 PSIG @ 200°F TYPE SR-H Learn More$400.00 -
RUPTURE DISC-2IN TC (75 PSI) 75°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 75PSIG @ 75°F Learn More$600.00 -
Hot
RUPTURE DISK-2IN TC (110 PSI) 200°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 110.00 PSIG @ 200°F TYPE AXIUS SC Learn More$400.00 -
RUPTURE DISC-1 1/2IN TC (130 PSI) 300°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 1 1/2IN TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 130.0 PSIG @ 300°F Learn More$1,368.00 -
RUPTURE DISC-2IN TC (88.3 PSI) 72°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 88.3 PSIG @ 72°F SR-H TYPE Learn More$400.00 -
RUPTURE DISC-2IN TC (25 PSI) 72°F (ASME) 316L EPDMThe rupture disc fits between 2IN TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Replace the disk every 5-6 years depending on the use of the tank to ensure superior performance. Learn More$689.00Out of stock -
StandpipeFor use in bottom-cone fermentation tanks, includes FDA silicone O-Ring Learn MoreAs low as $30.00 -
TC/Gas Fitting AssemblyThe TC x Gas Fitting is used to add a CO2-Nitrogen mix to your serving tank. We can also add a carbonation "stone" to the TC fitting and use the assembly to carbonate your beer. Learn MoreAs low as $45.65 -
TC CapThe TC cap is used to seal the end of a tube, fitting or valve which has a TC ferrule. A gasket and clamp attach the cap. 304 SS mat. Learn MoreAs low as $3.72
