Control & Monitoring
-
Ice shield with cut outThis ice shield features a 6 x 5 3/8 cut out for temp controller Learn More$125.00 -
ICE SHIELD-UNIVERSAL WITH FEET FITS U800, TANK NET, RANCO COMBOAn ice shield is commonly welded to tanks to be a universal mounting device for individual controllers. HOLE PATTERNS FIT: ACROLON TANKNET PL-1 CONTROLLER (6000 SERIES) CONTROLLER UE 800 CONTROLLER RANCO ETC-111000 Learn More$179.00 -
5/8" Level Gauge Compression FittingCompression fittings are used to connect the polysulphone and stainless steel tubing found in the level gauge assembly. Installation Directions: Tighten nut 'finger tight', continue to tighten 1-1/4" turns with a wrench. The small ferrule (2) will permanently adhere to level gauge tubing. CAUTION: Over tighten will result in fine fracture lines in the level gauge tubing. Learn MoreAs low as $29.95 -
(12) Sight Tube round5/8IN OD. Price below is per foot. To order please chose Qty: 1 foot = Qty 1 LEVEL GAUGE MUST BE ORDERED SEPARATELY Learn More$10.75 -
Fuji Temp & PartsThe Fuji controller receives information from the temperature sensor and sends open/close signals to the Heat Transfer Jacket solenoid valve. It can also operate direct fire Burners/Immersion Heaters/Etc. Learn MoreAs low as $35.00 -
Pressure GaugeThe range of a pressure gauge should be approximately twice the operating pressure of the vessel. ICC NW stocks 30 lb. Liquid filled gauges with 1/4 in. pipe thread connections. It is important to "burp" gauges periodically. Peel the black rubber stopper at the top of the valve back until pressure is released. Learn MoreAs low as $38.00 -
ThermometerThermometer face is 2-1/2 in. diameter and has a 1/2 in. MNPT threaded connection. Temperature range reads from 0 to 250 deg. F (-20 to 120 deg.C). Learn MoreAs low as $31.50 -
Level Gauge Valve & PartsThe 3-way level gauge valve will mount to a 1-1/2 IN TC at the base of a ICC NW level gauge system. This valve allows you to isolate the level gauge. 304 SS mat. The sight tube is translucent PFA Teflon. Make sure the tube insert is used at all tubing connections. Learn MoreAs low as $1.50 -
Valve-Level Gauge 1IN TCThe 3-way level gauge valve will mount to a 1-1/2 in. TC at the base of a ICC NW level gauge system. This valve allows you to isolate the level gauge. 304 SS mat. The sight tube is translucent PFA Teflon. Make sure the tube insert is used at all tubing connections. Learn More$177.75 -
5/8" Level Gauge Compression FittingCompression fittings are used to connect the polysulphone and stainless steel tubing found in the level gauge assembly. Learn MoreAs low as $29.95 -
Ice ShieldAn ice shield is commonly welded to tanks to be a universal mounting device for individual controllers. Learn MoreAs low as $125.00 -
ICE SHIELD-UNIVERSAL WITHOUT FEET FITS U800, TANK NET, RANCO COMBOAn ice shield is commonly welded to tanks to be a universal mounting device for individual controllers. HOLE PATTERNS FIT: ACROLON TANKNET PL-1 CONTROLLER (6000 SERIES) CONTROLLER UE 800 CONTROLLER RANCO ETC-111000 Learn More$128.00 -
Temperature SensorTemperature probe used to sense current product temperature. To be used in conjunction with a temperature controller. Sensors have a spring-loaded probe designed to fit a 12 in. tempwell with a 1/2 inch MNPT fitting. Learn MoreAs low as $136.85 -
Low Level SensorThe low level sensor is an on/off float switch. The float should mount at the low level limit of a tank. Most commonly used in a hot liquor tank. Learn MoreAs low as $244.50 -
Hi-Low Level ControlThe hi-low level control is used to regulate wort receiver levels. Commonly used on both the brewpub open wort receiver and the enclosed airless grant. Wetted parts are 316 Stainless Steel. Learn MoreAs low as $427.77 -
Tank Net PL-1The Tank Net PL-1 is a wireless tank thermostat specifically designed for use in wineries and breweries. Housed in a durable water-tight enclosure, the PL-1 offers stand-alone temperature control. Learn MoreAs low as $545.00
