Fittings & Valves
-
Mixer SealsParts for ICC NW Mixers including: bottom entry, side entry, top entry. Learn MoreAs low as $127.50 -
RUPTURE DISC-3IN TC (25 PSI) (ASME) 316LRUPTURE DISC-3IN TC (25 PSI) (ASME) 316L RATED 25.9 PSIG @ 72 DEG F RATED 23.52 PSIG @ 250 DEG F Learn More$400.00 -
RUPTURE DISC-2IN TC (60 PSI) 200°F (ASME) PTFE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 60.00 PSIG @ 200°F TYPE SR-H Learn More$400.00 -
In-Line Sight GlassThe in-line site glass is used for product viewing. The site glass has a TC ferrule on each end. The clear portion is either Pyrex or glass. One end unscrews to replace lens and gaskets. Learn MoreAs low as $129.00 -
RUPTURE DISC-2IN TC (75 PSI) 75°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 75PSIG @ 75°F Learn More$600.00 -
Hot
RUPTURE DISK-2IN TC (110 PSI) 200°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 110.00 PSIG @ 200°F TYPE AXIUS SC Learn More$400.00 -
RUPTURE DISC-2IN TC (50 PSI) 72°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 50.00 PSIG @ 72°F Learn More$400.00 -
RUPTURE DISC-1 1/2IN TC (130 PSI) 300°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 1 1/2IN TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 130.0 PSIG @ 300°F Learn More$1,368.00 -
RUPTURE DISC-2IN TC (88.3 PSI) 72°F (ASME) SILICONE 316LA rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. RATED 88.3 PSIG @ 72°F SR-H TYPE Learn More$400.00 -
RUPTURE DISC-2IN TC (25 PSI) 72°F (ASME) 316L EPDMThe rupture disc fits between 2IN TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Replace the disk every 5-6 years depending on the use of the tank to ensure superior performance. Learn More$689.00Out of stock -
Fuji Temp & PartsThe Fuji controller receives information from the temperature sensor and sends open/close signals to the Heat Transfer Jacket solenoid valve. It can also operate direct fire Burners/Immersion Heaters/Etc. Learn MoreAs low as $198.00 -
P.R.V.The P.R.V. are available for 2IN, 3IN and 4IN TC vent. Full 304 stainless steel body construction. Learn MoreAs low as $312.00 -
Hot
RUPTURE DISC-2IN TC (33.87 PSI) 72°F (ASME) 316LThe rupture disc fits between 2IN TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Replace the disk every 5-6 years depending on the use of the tank to ensure superior performance. RATED 33.87 PSIG @ 72°F Learn More$536.00 -
Temperature SensorTemperature probe used to sense current product temperature. To be used in conjunction with a temperature controller. Sensors have a spring-loaded probe designed to fit a 12 in. tempwell with a 1/2 inch MNPT fitting. Learn MoreAs low as $109.60 -
Low Level SensorThe low level sensor is an on/off float switch. The float should mount at the low level limit of a tank. Most commonly used in a hot liquor tank. Learn MoreAs low as $154.00 -
Hot
FLOAT SWITCH-SIDEWALL MOUNT 13.8 BAR FLOTECT L6EPB-B-S-3-AThe low level sensor is an on/off float switch. The float should mount at the low level limit of a tank. Most commonly used in a hot liquor tank. Learn More$154.00 -
Hi-Low Level ControlThe hi-low level control is used to regulate wort receiver levels. Commonly used on both the brewpub open wort receiver and the enclosed airless grant. Wetted parts are 316 Stainless Steel. Learn MoreAs low as $272.27 -
Sani-SpinThe Sani-Spin is used much the same way as a C.I.P. sprayball. The advantage of the Sani-Spin is the force of it’s spinning action and the minimal volume it requires. For example, the optimum operating condition for a C.I.P. sprayball is 40 GPM @ 25 PSI; where as the Sani-Spin requires just 25 GPM @ 30 PSI. Learn MoreAs low as $618.00 -
Oxy Carb Tee AssemblyThe tee assembly is used to inject gas into the product. A hollow capped tube of cintered stainless is welded to a TC ferrule and clamped to a customized TC tee. This assembly includes a special tee, cintered stone, check valve, 3/8" hose barb, clamp and gasket. 304 SS mat. Learn MoreAs low as $524.00
