Fittings & Valves

View as List Grid

Items 41-60 of 75

per page
Set Descending Direction
  1. FERRULE-DIN 25 IMPERIAL 1.0IN MALE (THREADED) 304 DIN 11851 UNION
    The DIN threaded ferrule is one side of a three piece DIN connection. The threaded ferrule connects to the female threaded DIN nut. 304 SS mat. Metric sizes available. Learn More
  2. Poly TC Cap
    The clear TC cap attaches to a TC ferrule for viewing. These caps are not designed to be used under pressure. Caution must be used in tightening the clamp as the cap can crack. Learn More
    As low as $8.85
  3. TC Clamp
    The TC clamp is used to clamp two TC ferrules together. A TC gasket is installed between the ferrule for a complete seal. 304 Stainless Steel. Learn More
    As low as $7.25
  4. TC Ferrule
    The TC ferrule is one end of a three part connection. This is the most commonly used type of sanitary process pipe connection. Ferrules have 1.125" necks. Longer and shorter necks are available. 304 Stainless Steel. Learn More
    As low as $0.00
  5. Rupture Disk
    A rupture disc is a secondary non-mechanical pressure protection system for your tank. The rupture disc fits between 2 in. TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Ask for a cut sheet for more information. Learn More
    As low as $589.00
  6. RUPTURE DISC-2IN TC (35 PSI) (ASME) 316L
    The rupture disc fits between 2IN TC fittings. It does not need a separate gasket. A rupture disc will protect your brewery and your patrons. It is extremely unwise and dangerous to operate a pressure tank without non-mechanical protection from over pressurization. Replace the disk every 5-6 years depending on the use of the tank to ensure superior performance. Learn More
  7. DIN Wrench
    The DIN wrench is used to fully tighten the DIN nut to the DIN ferrule Learn More
    As low as $41.50
  8. Sprayballs & Parts
    Sprayballs are used either for dispersing cleaning solution into a tank, or sparging onto a lauter tun grain bed. The sprayball slips onto tubing with a hairpin clip. 2-1/2 in. sprayballs slip over 1 in. tubing and will clean up to 5 foot diameter vessels. 3-1/2 in. sprayballs slip over 1-1/2 in. tubing and will clean up to 10 foot diameter vessels. Optimum operation: 40 GPM @ 25 PSI. 316 SS mat. Learn More
    As low as $4.95
  9. In-Line Sight Glass Lens
    The in-line site glass is used for product viewing. Order does include Replacement lense only. Learn More
    As low as $24.95
  10. In-Line Sight Glass Gasket
    The in-line site glass is used for product viewing. The site glass has a TC ferrule on each end. The clear portion is either Pyrex or glass. One end unscrews to replace lens and gaskets. Gaskets come in a package of 2 Learn More
    As low as $2.50
  11. In-Line Sight Glass 4-bolt
    The in-line site glass is used for product viewing. The site glass has a TC ferrule on each end. The clear portion is either Pyrex or glass. One end unscrews to replace lens and gaskets. Learn More
    As low as $138.60
  12. Sani-Spin
    The Sani-Spin is used much the same way as a C.I.P. sprayball. The advantage of the Sani-Spin is the force of it’s spinning action and the minimal volume it requires. For example, the optimum operating condition for a C.I.P. sprayball is 40 GPM @ 25 PSI; where as the Sani-Spin requires just 25 GPM @ 30 PSI. Learn More
    As low as $618.00
  13. P.A.M. Tree
    The P.A.M. Tree assembly groups the necessary fittings for tank pressure regulation together at the end of the vent extension line. The standard tree assembly consists of a pressure gauge, ball valve, and an open TC port. Does not include a P.R.V. Learn More
    As low as $228.00
  14. P.A.M. Spool
    The P.A.M. Spool Assembly groups the necessary fittings together for tank pressure regulation. The standard spool assembly consists of a pressure gauge, ball valve, and an open TC port. Does not include a P.R.V. Learn More
    As low as $110.10
  15. P.R.V. & Vacuum Parts
    Springs, Gaskets etc for P.R.V's Learn More
    As low as $2.95
  16. Replacement Coil - Solenoid Valve
    A brass Solenoid Valve is used to regulate coolant. The strength of brass is needed for the constant valve cycling. Learn More
    As low as $78.40
  17. Sample Valve MNPT
    The sample valve is designed to accommodate a CO2 test meter. Learn More
    As low as $118.50
  18. Check Valve
    A check valve with a ten pound spring is used with carbonation stone assemblies to prevent product back-flow. Check valves are available with male or female pipe thread connections. Learn More
    As low as $87.00
  19. Ball Valves
    The stainless steel ball valve has female threaded pipe connections, and is a "full port" valve (the flow is not restricted). 316 SS mat. Learn More
    As low as $30.98
  20. TC Tee
    The TC has three TC ferrules for multi-purpose application. Custom branch sizes and butt-weld tees available. 304 SS mat. Learn More
    As low as $26.75
View as List Grid

Items 41-60 of 75

per page
Set Descending Direction