Fittings & Valves
-
VALVE-SEAT DIAPHRAGM TC 1.5IN, BREWERY MIX VALVEVALVE-SEAT DIAPHRAGM TC 1.5IN, BREWERY MIX VALVE Learn More$24.00 -
Butterfly ValvesThe butterfly valve is used in process flow piping where fractional flow control is required. The valve has a stainless steel body with a silicon valve seat. TC connections shown. Other connections and butt-weld ends available on all butterfly valves. 304 SS mat. Learn MoreAs low as $120.92 -
Valve SeatsValve seats seal the valve body against the disk to stop flow. Learn MoreAs low as $12.65 -
Solenoid ValveA brass Solenoid Valve is used to regulate coolant. The strength of brass is needed for the constant valve cycling. Learn MoreAs low as $52.81 -
DIN NutThe DIN nut accompanies the plain DIN ferrule and is tightened with a DIN wrench. The nut serves the same function as a clamp in a TC connection. 304 SS mat. Metric sizes available. Learn MoreAs low as $12.30 -
DIN Ferrule, Threaded EndThe DIN threaded ferrule is one side of a three piece DIN connection. The threaded ferrule connects to the female threaded DIN nut. 304 SS mat. Metric sizes available. Learn MoreAs low as $12.34 -
Replacement Coil - Solenoid ValveA brass Solenoid Valve is used to regulate coolant. The strength of brass is needed for the constant valve cycling. Learn MoreAs low as $56.70 -
Check ValveA check valve with a ten pound spring is used with carbonation stone assemblies to prevent product back-flow. Check valves are available with male or female pipe thread connections. Learn MoreAs low as $138.00 -
Ball ValvesThe stainless steel ball valve has female threaded pipe connections, and is a "full port" valve (the flow is not restricted). 316 SS mat. Learn MoreAs low as $48.75 -
TC/Gas Fitting AssemblyThe TC x Gas Fitting is used to add a CO2-Nitrogen mix to your serving tank. We can also add a carbonation "stone" to the TC fitting and use the assembly to carbonate your beer. Learn MoreAs low as $45.65 -
TC TeeThe TC has three TC ferrules for multi-purpose application. Custom branch sizes and butt-weld tees available. 304 SS mat. Learn MoreAs low as $25.60 -
TC Eccentric ReducerEccentric reducers are used for tubing size transitions. The flat side allows complete drainage in horizontal piping. Custom reducers, additional sizes and butt-weld available. 304 SS mat. Learn MoreAs low as $25.25 -
TC Concentric ReducerConcentric reducers are used for TC transitions in vertical tubing. Custom reducers, additional sizes and butt-weld available. 304 SS mat. Learn MoreAs low as $19.00
-
TC 90° ElbowThe 90° elbow has TC connections on each end. TC elbows allow lines to be broken down for sanitizing. Butt-weld elbows available. 304 or 316L SS mat. Learn MoreAs low as $22.16 -
TC Cap x TC Ferrule (offset)TC cap adapters are an economical alternative to an eccentric reducer. This fitting is used to reduce the size in process piping where turbulence and complete drainage of the product is not a concern. 304 SS mat. Learn MoreAs low as $25.34 -
TC Cap x TC Ferrule (centered)TC adapters are an economical alternative to a concentric reducer. This fitting is used to reduce the size in process piping where turbulence and complete drainage of the product is not a concern. 304 SS mat. Learn MoreAs low as $13.75 -
TRI CLAMP x FNPTA TC x FNPT will adapt a TC ferrule to male pipe fittings. One end is a TC, the other is female threaded pipe. 304 SS mat. Learn MoreAs low as $10.25 -
TRI CLAMP x MNPTA TC x MNPT will adapt a TC (TRI-CLAMP) ferrule to female pipe fittings. One end is TC and the other is male threaded pipe. 304 SS mat. Learn MoreAs low as $13.75
